Grand Design Momentum Owner'S Manual Download Page 152

Page: 152 / 220

150

Electronics

TV Reception Basics

TV broadcasting is a point-to-point communication. Any ob-

structions between the transmitter and the antenna will de-

grade the signal, affecting picture quality.

• Television stations transmit their broadcast signal

"over the air" to surrounding areas.

• TV antennas are designed to receive the broadcast

signals.

• Picture quality depends on the antenna type

and your distance from the transmitter.

• The further you are from the transmitter, the weaker

the signal becomes, affecting picture quality.

TV Signal Booster

•

The TV Signal Booster must be turned ON for

improved

antenna

reception.

• The TV Signal Booster sends 12-volt DC power to the TV

roof antenna. This voltage energizes the transistors in the

antenna head amplifier.

• Turn OFF

the

TV Signal Booster

to view cable/satellite TV,

or to use a DVD/Blu-ray player or Game System.

Cable/Satellite Outlet

Both Cable and Satellite connection outlets are found in the

outside utility center.

• The

Cable

input connects to an RG6 cable run through

in-line splitters to provide service at multiple locations.

• The

Satellite

inputs connect to RG6 cables run directly

to specific locations (no splitters). This allows for clean

transfer of HD signals from the satellite dish.

Please refer to the (customer supplied) satellite manufacturer

manual for setup, care and maintenance instructions

Many television

stations have

changed from VHF

to UHF channels.

UHF channels operate at

higher frequencies; the

signal does not travel as

far as those of VHF. If your

TV is digital, you do not

need a converter box or

any other external, add-on

device. If your antenna was

working prior to the digital

change, it is probably

working now. Check the

TV or the settings if you

have problems receiving

DTV channels. For more

troubleshooting tips, go to

https://kingconnect.com

Summary of Contents for Momentum





























































































































































































































Search results

Summary of Contents for Momentum

Reviews:

Related manuals for Momentum

Brands by name

Popular brands

Grand Design Momentum, Owner'S Manual

Search results

Summary of Contents for Momentum

Reviews:

Related manuals for Momentum

Brands by name

Popular brands