Grand Design Momentum Owner'S Manual Download Page 82

Page: 82 / 220

Towing & Leveling

Towing the RV, Continued

Parking

After the RV is in the desired location, set the tow vehicle parking

brake and place the transmission in park. Turn OFF the ignition

switch. Go outside and block the RV wheels securely with wheel

chocks. The wheel chocks can be wood blocks or purchased

items as long as they prevent the RV from rolling.

Unhitching from the Tow Vehicle

1. Choose a mostly level place to park, and

pull the RV into the site.

2. Block the wheels to keep the RV from rolling.

3. LOWER the landing legs to stabilize the RV.

• For proper operation, it is important to follow the

manufacturer’s instructions.

4. Disconnect the wire harness/connector plug.

5. Disconnect the breakaway switch lanyard.

6. OPEN the truck tailgate.

• Unless your truck is equipped with a tailgate

designed to accommodate a FW hitch.

7. Shift your truck into reverse,

but

DO NOT press on the accelerator.

• This moves the kingpin off the locking bar,

so that it can be disengaged.

8. Apply the brakes,

then

Set your parking brake.

9. Disengage the locking bar,

then

Unhitch the RV.

10. Pull away your tow vehicle.

11. Level the RV (front to back) by adjusting the

fifth-wheel height.

If the parking spot

is on asphalt on a

very hot day or on

dirt and/or gravel, a

block of wood under each

jack leg can be used to

spread the load and reduce

the possibility of the leg

sinking into the surface.

Summary of Contents for Momentum





























































































































































































































Search results

Summary of Contents for Momentum

Reviews:

Related manuals for Momentum

Brands by name

Popular brands

Grand Design Momentum, Owner'S Manual

Search results

Summary of Contents for Momentum

Reviews:

Related manuals for Momentum

Brands by name

Popular brands