background image

Supply System Operation 

12

3A2798D

Change Drums 

1.

Close the air motor ball valve (BF) to stop the pump.

2.

Press and hold the blowoff air button (BG) then set 
ram director valve (BC) to UP to raise the platen (D) 
until the platen (D) is completely out of drum. When 
the ram exits the pail, release the blowoff air button 
to allow the ram to rise to its full height. Use mini-
mum amount of air pressure necessary to push the 
platen out of the drum. 

3.

Remove empty drum.

4.

Inspect platen and, if necessary, remove any 
remaining material or material build-up.

5.

Place full drum on ram base.

6.

Lower the ram and adjust the position of the drum 
relative to the platen. Se

Start and Adjust Ram 

on 

page 11.

Flush

1.

Remove platen from pump, then submerge pump 
into solvent. To clean platen, gently wipe with sol-
vent. 

NOTE:

 Read notice table in 

Flush Before 

Using Equipment

 section, page 10.

2.

Perfor

Start and Adjust Ram 

on page 11 to pres-

surize the pump with solvent.

3.

Hold gun firmly against a grounded pail and trigger 
gun into pail until clean solvent dispenses.

Shutdown and Care of the Pump

1.

Set the ram director valve (BC) to DOWN.

2.

Follow the 

Pressure Relief Procedure 

on page 10.

3.

Follow the pump shutdown instructions in Xtreme 
lowers manual. See 

Related Manuals

 on page 2.

Replace Throat Seals

Remove wet cup from displacement pump while 
attached to the ram to replace throat seals. 

1.

Follow the 

Pressure Relief Procedure 

on page 10.

2.

Remove Quick Coupler

.

3.

Remove wet cup and packing cartridge according to 
instructions in Xtreme lowers manual. See 

Related 

Manuals

 on page 2.

Remove Quick Coupler

1.

Ensure displacement pump is at bottom of stroke.

2.

Follow the 

Pressure Relief Procedure 

on page 10.

3.

Remove clip (GC), and slide coupling cover (GB) up 
to remove coupling (GA).

Excessive air pressure in the material drum could 
cause the drum to rupture, causing serious injury. 
The platen must be free to move out of the drum. 
Never use drum blowoff air with a damaged drum.

NOTICE

To prevent material from curing in the system, imme-
diately flush the system when a pressure drop is 
noticed during spraying and when done spraying.

GB

GC

GA

ti20249a

Summary of Contents for Xtreme PFP 16P957



































Reviews: