Graco Xtreme PFP 16P957 Instructions - Parts Manual Download Page 2

Page: 2 / 34

Related Manuals

3A2798D

Contents

Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Component Identification . . . . . . . . . . . . . . . . . . . . 5

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

General Information . . . . . . . . . . . . . . . . . . . . . . 8

Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Connect Mix Line and Gun . . . . . . . . . . . . . . . . . 9

Mechanical Setup . . . . . . . . . . . . . . . . . . . . . . . . 9

Attach Drum Stops . . . . . . . . . . . . . . . . . . . . . . . 9

Supply System Operation . . . . . . . . . . . . . . . . . . . 10

Before Operating . . . . . . . . . . . . . . . . . . . . . . . . 10

Pressure Relief Procedure . . . . . . . . . . . . . . . . 10

Flush Before Using Equipment . . . . . . . . . . . . . 10

Start and Adjust Ram . . . . . . . . . . . . . . . . . . . . 11

Start and Adjust Pump . . . . . . . . . . . . . . . . . . . 11

Change Drums . . . . . . . . . . . . . . . . . . . . . . . . . 12

Flush . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Shutdown and Care of the Pump . . . . . . . . . . . 12

Replace Throat Seals . . . . . . . . . . . . . . . . . . . . 12

Remove Quick Coupler . . . . . . . . . . . . . . . . . . . 12

Before Beginning Repair . . . . . . . . . . . . . . . . . . . 13

Maintenance Procedures . . . . . . . . . . . . . . . . . . . 13

Platen Maintenance . . . . . . . . . . . . . . . . . . . . . 13

Adjust Spacers . . . . . . . . . . . . . . . . . . . . . . . . . 13

Remove and Reinstall Wiper . . . . . . . . . . . . . . 14

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Disconnect Pump from Platen . . . . . . . . . . . . . . 17

Connect Platen to Pump . . . . . . . . . . . . . . . . . . 17

Remove Wipers . . . . . . . . . . . . . . . . . . . . . . . . . 17

Install Wipers . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Disconnect Displacement Pump . . . . . . . . . . . . 18

Remove Displacement Pump . . . . . . . . . . . . . . 18

Install Displacement Pump . . . . . . . . . . . . . . . . 18

Connect Displacement Pump . . . . . . . . . . . . . . 18

Remove Air Motor . . . . . . . . . . . . . . . . . . . . . . . 19

Install Air Motor . . . . . . . . . . . . . . . . . . . . . . . . . 19

Supply Unit Repair . . . . . . . . . . . . . . . . . . . . . . . 20

Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Check Valve (16T481) . . . . . . . . . . . . . . . . . . . . 29

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Static Mixer Kit, 16T316 . . . . . . . . . . . . . . . . . . 30

Static Mixer (16T316) . . . . . . . . . . . . . . . . . . . . 30

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

G raco Standard Warranty . . . . . . . . . . . . . . . . . . . 34

Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . 34

Related Manuals

The following manuals are available at www.graco.com.
Component Manuals in English:

Manual

Description

311762

Xtreme Lowers Instructions-Parts

311238

NXT

Air Motor Instructions-Parts

Summary of Contents for Xtreme PFP 16P957



































Search results

Summary of Contents for Xtreme PFP 16P957

Reviews:

Related manuals for Xtreme PFP 16P957

Brands by name

Popular brands

Graco Xtreme PFP 16P957, Instructions - Parts Manual

Search results

Summary of Contents for Xtreme PFP 16P957

Reviews:

Related manuals for Xtreme PFP 16P957

Brands by name

Popular brands