background image

19

ACCESSORIES

USE GENUINE GRACO PARTS AND ACCESSORIES

Must be purchased separately.

NYLON FLUID HOSE

184–138

3/4 npt (mbe); 4.8 m (15 ft) long

276 bar (4000 psi) MAXIMUM WORKING PRESSURE

184–139

1/2 npt (mbe); 1.5 m (5 ft) long

184–156

1/2 npt (mbe); 6.1 m (20 ft) long

215–244

3/8 npt (mbe); 7.6 m (25 ft) long

350 bar (5000 psi) MAXIMUM WORKING PRESSURE

EXTRUSION FLO GUN 207–945

420 bar (6000 psi) MAXIMUM WORKING PRESSURE

Pistol–type trigger. 1/2 npt(f) inlet.

0242

GUN SWIVELS

420 bar (6000 psi) MAXIMUM WORKING PRESSURE

To connect the fluid hose to the gun, and allow freer gun

movement. For non–abrasive fluids.

207–947

Straight swivel; 1/2 npt(f) x 1/2 npt(m)

207–948

Zee swivel; 1/2 npt(f) x 1/2 npt(m)

SINGLE POST 19 LITER (5 GALLON) RAM 222–781

For extruding highly viscous fluids from 19 liter (5 gallon)

pails. Use with wiper plate 222–812. Refer to Instruction

Manual 306–838.

0210

PNEUMATIC ELEVATOR CART 224–137

Elevator uses air pressure to raise pump from 19 liter (5

gallon) pails. Release of air pressure and weight of the

pump cause it to move downward. Use with wiper plate

222–812. Also requires Cart Accessory Kit 224–376. Re-

fer to Instruction Manual 308–092.

0211

CART ACCESSORY KIT 224–376

Required to mount a Check–Mate 200 Pump on Pneu-

matic Elevator Cart 224–137. Includes instructions.

19 LITER (5 GAL.) WIPER PLATE 222–812

PATENT PENDING

For use with 222–781 ram and 224–137 Pneumatic

Cart. Applies pressure on surface of highly viscous

fluids, to force fluid into the pump intake and assist prim-

ing. 

Refer to Instruction Manual 308–049.

0212

RAM MOUNTING KIT 224–829

Provides mounting hardware to install a Check–Mate

200 pump on a 200 liter (55 gallon) two post ram, Models

207–279 or 223–634. Refer to Instruction Manual

308–027.

RAM ACCESSORY KIT 223–881

Provides air hose and air line fittings necessary for

mounting a Check–Mate 200 pump on a 200 liter (55 gal-

lon) two post ram, Models 207–279 or 223–634. Refer to

Instruction Manual 308–027.

GRACO THROAT SEAL LIQUID

Non–evaporating liquid for wet cup

206–995

0.95 liter (1 quart)

206–996

3.8 liter (1 gallon)

Summary of Contents for Metric CHECK-MATE 200






























Reviews: