background image

Maintenance

Maintenance

Maintenance Schedule

Establish a preventive maintenance schedule

based on the pump’s service history. Scheduled

maintenance is especially important to prevent spills

or leakage due to diaphragm failure.

Lubrication

The pump is lubricated at the factory. It is designed

to require no further lubrication for the life of the

packings. There is no need to add an inline lubricator

under normal operating conditions.

Tighten Threaded Connections

Before each use, check all hoses for wear or damage

and replace as necessary. Check to be sure all

threaded connections are tight and leak-free. Check

mounting bolts. Check fasteners. Tighten or retorque

as necessary. Although pump use varies, a general

guideline is to retorque fasteners every two months.

See

Torque Instructions, page 16

.

Flushing and Storage

• Flush before fluid can dry in the equipment, at the

end of the day, before storing, and before repairing

equipment.

• Flush at the lowest pressure possible. Check

connectors for leaks and tighten as necessary.

• Use solvent that is compatible with the equipment

wetted parts and the material being dispensed.

• Always flush the pump and relieve the pressure

before storing it for any length of time.

NOTICE

Flush the pump often enough to prevent the fluid

you are pumping from drying or freezing in the

pump and damaging it.

3A2578C

15

Summary of Contents for Husky 2200F

























Reviews: