background image

Operation

Operation

Pressure Relief Procedure

Follow the Pressure Relief Procedure

whenever you see this symbol.

This equipment stays pressurized until pressure

is relieved manually. To help prevent serious

injury from pressurized fluid, such as splashing

in the eyes or on skin, follow the Pressure Relief

Procedure when you stop pumping and before you

clean, check, or service the equipment.

1. Shut off the air supply to the pump.
2. Open the dispensing valve, if used.
3. Open the fluid drain valve to relieve fluid

pressure. Have a container ready to catch the

drainage.

Tighten Fasteners

Before mounting and using the pump for the first time,

check and retorque all external fasteners. Follow

Torque Instructions, page 16

, or see the torque

tag on your pump. After the first day of operation,

retorque the fasteners.

Flush the Pump Before First Use

The pump was tested in water. If water could

contaminate the fluid you are pumping, flush the

pump thoroughly with a compatible solvent. See

Flushing and Storage, page 15

.

Start and Adjust the Pump

1. Be sure the pump is properly grounded. See

Ground The System, page 10

.

2. Check fittings to be sure they are tight. Use a

compatible liquid thread sealant on male threads.

Tighten fluid inlet and outlet fittings securely

3. Place the suction tube (if used) in fluid to be

pumped.
NOTE: If fluid inlet pressure to the pump is more

than 25% of outlet working pressure, the ball

check valves will not close fast enough, resulting

in inefficient pump operation.

NOTICE

Excessive fluid inlet pressure can reduce

diaphragm life.

4. Place the end of the fluid hose into an appropriate

container.

5. Close the fluid drain valve.
6. Turn the air regulator knob to 0. Open all

bleed-type master air valves.

7. If the fluid hose has a dispensing device, hold

it open.

8. Slowly increase air pressure with the air regulator

until the pump just starts to cycle. Allow the

pump to cycle slowly until all air is pushed out of

the lines and the pump is primed.
NOTE: Use lowest possible air pressure to prime,

just enough to cycle the pump. If the pump does

not prime as expected, turn air pressure DOWN.

9. If you are flushing, run the pump long enough to

thoroughly clean the pump and hoses.

10. Close the bleed-type master air valve.

Pump Shutdown

At the end of the work shift and before you check,

adjust, clean, or repair the system, follow the

Pressure Relief Procedure, page 14

.

14

3A2578C

Summary of Contents for Husky 2200F

























Reviews: