background image

Installation

Flange Connections

The fluid inlet and outlet ports are 2 in. (50 mm)

raised face, ANSI/DINPN10 flanges. Connect 2 in.

(50 mm) plastic pipe flange to the pump as follows.

You will need:
• Torque wrench
• Adjustable wrench
• 6 in. (152 mm) diameter, 1/8 in (32 mm) thick

PTFE gasket, with four 0.75 in (19 mm). diameter

holes on a 4.75 in. (121 mmm) diameter bolt circle,

and a 2 in. (50 mm) diameter center

• Four 5/8 in (17 mm) x 3 in (76 mm) long bolts
• Four 5/8 in.(17 mm) spring lock washers
• Eight 5/8 in. (17 mm) flat washers
• Four 5/8 in. (17 mm) nuts

1. Place a flat washer (K) on each bolt (H).
2. Align the holes in the gasket (G) and the pipe

flange (F) with the holes in the pump outlet flange

(E).

3. Lubricate the threads of the four bolts. Install

the bolts through the holes and secure with the

washers (K), lock washers (J), and nuts (L).

4. Hold the nuts with a wrench. Refer to the

tightening sequence in the figure and torque

the bolts to 20 to 30 ft-lb (27 to 41 Nm). Do not

overtorque.

5. Repeat for the pump inlet flange.

Figure 1

D

2 in. (50 mm) fluid inlet flange

E

2 in. (50 mm) fluid outlet flange

F

Plastic pipe flange

G

PTFE gasket

H

Bolt

J

Lock washer

K

Flat washer

L

N

ut

Lubricate threads. torque to 20 to 30 ft-lb

(27 to 41 N m). Do not overtorque.

3A2578C

13

Summary of Contents for Husky 2200F

























Reviews: