Graco HTX 2030 Operation Manual Download Page 2

Page: 2 / 28

Contents

313888E

Contents

Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 5

HTX 2030 with Base Coat Pump (257369) . . . . . 5

Top Coat Pump (Kit 24B140) . . . . . . . . . . . . . . . 6

Component Identification - Sprayer . . . . . . . . . . . 7

Component Identification - Base Coat Applicator 8

Component Identification - HTX2030 Air Spray

Trigger Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Pressure Relief Procedure . . . . . . . . . . . . . . . . . . 10

Applicator (Base Coat Pump) . . . . . . . . . . . . . . 10

Spray Gun (Top Coat Pump) . . . . . . . . . . . . . . 11

Start Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Material and Sprayer Preparation . . . . . . . . . . . 13

Prime Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Spray With Airless Tip . . . . . . . . . . . . . . . . . . . . 14

Spray Without Air - Clear Clog . . . . . . . . . . . . . 15

Air Assisted Spray

(Base Coat Applicator) . . . . . . . . . . . . . . . . 15

Air Assisted Spray

(Air Spray Trigger Gun) . . . . . . . . . . . . . . . 16

Spray Gun (Top Coat Pump) . . . . . . . . . . . . . . 17

Cleanup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Digital Tracking System (DTS) . . . . . . . . . . . . . . . 21

Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Secondary Menu - Stored Data Mode . . . . . . . 22

Digital Display Messages . . . . . . . . . . . . . . . . . . . 23

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 28

Summary of Contents for HTX 2030





























Search results

Summary of Contents for HTX 2030

Reviews:

Related manuals for HTX 2030

Brands by name

Popular brands

Graco HTX 2030, Operation Manual

Search results

Summary of Contents for HTX 2030

Reviews:

Related manuals for HTX 2030

Brands by name

Popular brands