Graco HTX 2030 Operation Manual Download Page 18 | Manualshive

Page: 18 / 28

background image

Cleanup

18

313888E

Cleanup

1.

Turn on/off switch OFF.

2.

Perform

Pressure Relief

procedure, page 10.

3.

Place pump in pail of clean water.

4.

Shut OFF air if spraying with air. Remove applicator
from material and air hoses.

5.

Base Coat Pump:

Disconnect material hose from

pump outlet.

6.

Insert wet cleaning ball into hose (Base Coat Only).
Connect material hose to pump outlet.

7.

Hold material hose over waste pail.

8.

Turn on/off switch ON and prime switch ON, or
applicator switch on material hose.

ti10796b

ti13644a

ti14284a

ti21040a

ti13639a

ti13643a

ti13638a

ti13640a

ti10795b

«
...
16
17
18
19
20
...
»

Summary of Contents for HTX 2030





























Reviews:

No comments

Related manuals for HTX 2030

Brand: WAGNER Pages: 40

Brand: Sagola Pages: 24

OZONATOR OA 1524

Brand: Ogawa Pages: 8

Brand: Ozito Pages: 7

CLEANline 333 FA

Brand: Solo Pages: 9

Brand: Solo Pages: 4

Brand: Tomahawk Pages: 28

Brand: F/S Manufacturing Pages: 3

Brand: Larius Pages: 32

Brand: Graco Pages: 10

HT19-401-003-15

Brand: Hyper Tough Pages: 32

Brand: Tritech Pages: 24

Brand: SMK Sprayers Pages: 8

Brand: Valex Pages: 13

Brand: Zenoah Pages: 14

Brand: Zenoah Pages: 9

SprayStation HV2901P

Brand: Earlex Pages: 36

COLOR-CATALOG-2004 ENGLISH

Brand: WAGNER Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands