Graco HTX 2030 Operation Manual Download Page 11 | Manualshive

Page: 11 / 28

background image

Pressure Relief Procedure

313888E

11

Spray Gun (Top Coat Pump)

1.

Lock gun trigger safety and turn engine OFF.

2.

Turn on/off switch to OFF and turn pressure control
knob fully counterclockwise.

3.

Unlock trigger safety. Hold metal part of gun firmly
to side of grounded metal pail and trigger gun to
relieve pressure.

4.

Lock gun trigger safety. Open pressure prime/drain
valve. Leave valve open until ready to spray again.

NOTE:

If you suspect that the spray tip nozzle or hose is

completely clogged, or that pressure has not been fully
relieved after following the previous steps, VERY
SLOWLY loosen the tip guard retaining nut or hose end
coupling to relieve pressure gradually, then loosen com-
pletely. Then clear tip or hose.

ti13131a

ti13050a

ti10796b

ti13128a

ti13130a

ti13131a

ti14632a

«
...
9
10
11
12
13
...
»

Summary of Contents for HTX 2030





























Reviews:

No comments

Related manuals for HTX 2030

6002 Big B.O.S.S.

Brand: Mytee Pages: 16

Brand: Hozelock Pages: 8

Brand: Graco Pages: 16

Brand: Easylife Pages: 2

Brand: Würth Pages: 78

Brand: Sagola Pages: 24

Brand: WAGNER Pages: 56

Brand: XPOtool Pages: 6

PERFORMANCE PLUS 8199N

Brand: King Canada Pages: 10

Walcom GENESI CARBONIO 360 EVO HALO BASE

Brand: WALMEC Pages: 56

Brand: Feider Machines Pages: 32

Brand: Sagola Pages: 52

Brand: Sunex Pages: 18

AIRLESS PLA K11435

Brand: Larius Pages: 12

Brand: DeVilbiss Pages: 6

Brand: Tecomec Pages: 4

Brand: Graco Pages: 20

Brand: Hardi Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands