Graco HTX 2030 Operation Manual Download

Page: 1 / 28

Operation

HTX 2030

-For Portable Airless and Air-Assisted Spraying of Water-Based Architectural Coatings with Base Coat Pump-
-For Airless Spraying Architectural Coatings and Paints with Top Coat Pump-

Model Number: 257369 (HTX2030 FreeFlo Inline Gun)
Model Number: 278675 (HTX2030 AirSpray Trigger Gun)

Maximum Working Pressure:

Base Coat Pump:

1000 psi (69 bar, 6.9 MPa)

Top Coat Pump:

3300 psi (228 bar, 22.8 MPa)

Related Manuals

313891

- Operation (French)

313893

- Operation (Spanish)

313889

- Repair (English)

313892

- Repair (French)

313893

- Repair (Spanish)

313890

- Parts

313895

- HTX 2030 Flex Head and Pole Spray Applicator (English)

313896

- HTX 2030 Flex Head and Pole Spray Applicator (French)

313897

- HTX 2030 Flex Head and Pole Spray Applicator (Spanish)

310894

- Displacement Pump (Top Coat)

308491

- Airless Heavy Duty Texture Gun

313537

- HTX 2030 FreeFlo Inline Gun (English)

313603

- HTX 2030 FreeFlo Inline Gun (Chinese)

313908

- HTX 2030 FreeFlo Inline Gun (French)

313911

- HTX 2030 FreeFlo Inline Gun (Spanish)

332160

- HTX2030 AirSpray Trigger Gun (English)

332227

- HTX2030 AirSpray Trigger Gun (French)

332228

- HTX2030 AirSpray Trigger Gun (Spanish)

332229

- HTX2030 AirSpray Trigger Gun (Chinese)

IMPORTANT SAFETY INSTRUCTIONS

Read all warnings and instructions in this
manual. Save these instructions.

313888E

ti13632a

Summary of Contents for HTX 2030





























Search results

Summary of Contents for HTX 2030

Reviews:

Related manuals for HTX 2030

Brands by name

Popular brands

Graco HTX 2030, Operation Manual

Search results

Summary of Contents for HTX 2030

Reviews:

Related manuals for HTX 2030

Brands by name

Popular brands