background image

Warnings 

4

3A5919A

Battery Disposal

Do not place batteries in the trash. Recycle batteries according to local regulations. In the USA and Canada call 
1-800-822-8837 to find recycling location or go to 

www.call2recycle.org.

WARNING

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in 

work area

 can ignite or explode. To help pre-

vent fire and explosion:

Use equipment only in well ventilated area.

Do not fill fuel tank while engine is running or hot; shut off engine and let it cool. Fuel is flammable 
and can ignite or explode if spilled on hot surface.

Keep work area free of debris, including solvent, rags and gasoline.

Keep a fire extinguisher in work area.

CARBON MONOXIDE HAZARD

Exhaust contains poisonous carbon monoxide, which is colorless and odorless. Breathing carbon 
monoxide can cause death. 

Do not operate in an enclosed area.

BATTERY HAZARD 

Lead-acid batteries produce explosive gases and contain sulfuric acid that can cause severe burns. To 
avoid sparks and injury when handling or working with a lead-acid battery:

Read and follow the battery manufacturer’s warnings.

Exercise caution when working with metallic tools or conductors to prevent short circuits and sparks.

Keep all sparks, flames, and cigarettes away from batteries.

Always wear protective eyewear and protective equipment for face, hands, and body.

If you have direct contact with battery fluid, flush with water and consult a physician immediately.

Installation and maintenance must be performed by knowledgeable personnel only.

CALIFORNIA PROPOSITION 65

The engine exhaust from this product contains a chemical known to the State of California to cause 
cancer, birth defects or other reproductive harm.
This product contains a chemical known to the State of California to cause cancer, birth defects or 
other reproductive harm. Wash hands after handling.

Summary of Contents for GrindLazer 25M992





















Reviews: