Graco EM5 238457 Instructions-Parts List Manual Download

Page: 1 / 24

CAUTION

This dispense valve is designed to dispense
petroleum-based lubricants and antifreeze only.

Do not dispense windshield washer solvent
with this dispense valve.

This dispense valve is designed for indoor use
only.

This dispense valve is not designed for in-line
installation. Do not install with a shut-off valve
on the outlet side of the meter. Such installa-
tion could result in damage to the meter hous-
ing cover.

Instructions – Parts List

GRACO INC.ąP.O. BOX 1441ąMINNEAPOLIS, MNą55440-1441

STANDARD

EM5

Electronic Metered

Dispense Valves

For dispensing petroleum–based lubricants and antifreeze.

1000 psi (7 MPa, 69 bar) Maximum Working Pressure
5 gpm (18.9 lpm) Maximum Flow Rate

Factory-Set to Measure in Liters
Canadian Weights & Measures approved

Model 238457

bend 3/8–in. rigid tube

Model 238458

3/8–in. coupled flexible hose

Model 238459

bend 3/8–in. gear lube tube, 90

elbow

308487P

Model 238457 shown

06042C

Registered Design No. 1025804

INTRINSICALLY SAFE FOR
HAZARDOUS LOCATIONS
CLASS 1, DIV. 1, GROUP D

97D.122550

EExia II A/B T3

Important Safety Instructions.

Read all warnings and instructions in this manual.
Save these instructions.

Parts

Summary of Contents for EM5 238457

























Search results

Summary of Contents for EM5 238457

Reviews:

Related manuals for EM5 238457

Brands by name

Popular brands

Graco EM5 238457, Instructions-Parts List Manual

Search results

Summary of Contents for EM5 238457

Reviews:

Related manuals for EM5 238457

Brands by name

Popular brands