background image

Operation 

14

312668ZAC

Calibration 

Recalibrate the meter for dispensing different fluids.

1. If the Calibration Screen is not already displayed, 

complete steps 1 - 3 of the 

Setup Menus, 

page 12.

2. CAL

 

blinks indicating the Calibration Menu screen.

3. Do one of the following:

Use the current calibration.

• Press and hold the Auto / 

Reset button to lock in 

the displayed amount. 

The display advances to 

the Auto Preset Amount 

Menu.

or

Recalibrate the meter:

a. If the unit of measurement is gallons, pints, 

or quarts, dispense exactly one (1) quart of 

fluid into a calibrated one (1) quart container. 

If the unit of measurement is liters, dispense 

exactly one (1) liter of fluid into a calibrated 

one (1) liter container.

 

For proper calibration, the exact amount 

must be dispensed.

b. Press and hold the

 

Manual / Reset button 

until CAL stops blink

-

ing. 

c. When CAL starts to 

blink again, the display 

should show 1.00, 

which indicates the new calibration is com

-

plete.

NOTE: If an error was made during meter recalibration, 

repeat steps a - c of the recalibration process.

d. Press and hold the 

Auto / Reset button to 

advance to the Auto 

Preset Amount Menu.

Auto Preset Amount

Specifies an amount displayed when in Auto Dispense 

Mode. Typically, enter the amount most frequently dis

-

pensed.

1. If the Auto Preset Amount screen is not already dis

-

played, complete steps 1 - 3 of the 

Setup Menus

, 

page 12.

F

IG

. 14

GAL

QTS

PTS

LITERS
R-TOTAL

CAL

ti12056a

F

IG

. 15

GAL

QTS

PTS

LITERS
R-TOTAL

AUTO

ti12082a

Summary of Contents for 24F883































Reviews: