background image

Installation

312668ZAC

7

Installation

This dispense valve must be calibrated after installation 

(beginning on page 14). Dispense amounts vary with 

fluid pressure, temperature, and type of fluid 

dispensed.

This dispense valve is designed for indoor use only, for 

use with industrial grade batteries (see page 21), and is 

not designed for in-line installation.

Grounding

Pump:

 follow the manufacturer’s recommendations.

Hose Reels or consoles

: connect to a true earth 

ground.

Fluid hoses:

 use only conductive hoses when 

dispensing petroleum products.

To maintain grounding continuity when flushing or 

relieving pressure, hold a metal part of the valve firmly 

to the side of a grounded metal pail, then trigger the 

valve.

Pre-Installation Procedure

1. Install the battery. See 

Replace the Battery

, 

page 21.

2. Follow the 

Pressure Relief Procedure

, page 10.

3. Close the shut off valve (B) (F

IG

. 1, page 6).

4. Ground the hose and reel or counsel. See 

Grounding

.

NOTE: Leave at least two engaged threads bare when 

using PTFE tape, the bare threads ensure ground is 

maintained.

Installation Procedure

For existing installations, skip to 

Electronic Control (1) 

and Gasket (2) Installation

, page 8.

Flush the System 

1. Close the fluid shut off valve (B) at each dispense 

position (F

IG

. 3).

2. Make sure that the main fluid outlet valve at the 

pump is closed.

3. Adjust the air pressure to the pump motor.

a. Adjust the air regulator attached to the motor 

air inlet.

b. Open the air valve.

c. Slowly open the main fluid valve.

4. Flush the system:

a. Place the hose end (no dispense valve 

connected) into a container for waste oil.

b. Secure the hose in the container so it does not 

come out during flushing.

c. For multiple dispense positions, start with the 

dispense position furthest from the pump, and 

work toward the pump.

5. Slowly open the shut off valve (B) at the dispense 

position and flush out a sufficient amount of oil to 

ensure that the entire system is clean (F

IG

. 3).

6. Close the shut off valve (B) (F

IG

. 3).

7. Repeat steps and 6 at all of the dispense 

positions.

The equipment must be grounded to reduce the risk 

of static sparking. Static sparking can cause fumes 

to ignite or explode. Grounding provides an escape 

wire for the electric current.

NOTICE

For new installations, or when there is contaminated 

fluid in the lines, flush the lines before installing the 

meter valve, to avoid valve leakage. 

Summary of Contents for 24F883































Reviews: