Gossen MetraWatt PROFITEST 204 Operating Instructions Manual Download Page 43 | Manualshive

Page: 43 / 76

Gossen MetraWatt PROFITEST 204 Operating Instructions Manual Download Page 43

GMC-I Messtechnik GmbH

43

5.1.1

Entering a Description

MENU

Description

Description

:

Descriptions can be entered for the
various systems. The description is
displayed and subsequently printed out when the respective sys-
tem is selected.

Note:

An ID number should be entered for each system if PS3

software is used. Enter the number in parentheses. The system
description appears to the right of the ID number (see illustration
above). Parentheses are entered by pressing and holding the shift
key, and simultaneously pressing the number keys 8 and 9.

Descriptions can be entered in two different ways:

– Convenient Entry with the SI Module (optional)

Descriptions can be entered with the alphanumeric keypad at
the SI module (see operating instructions included with the

SECUTEST SI+

).

– Entry with the Keys at the PROFITEST 204+

Select letters, numbers or characters.

STORE

Move the entry cursor left.

START

Move the entry cursor right.

MENU

Entered data must be acknowledged with the MENU key.
The previously entered data are then saved to memory.
Alternatively, data can be saved by pressing the STORE key at the
SI module.

Up to 250 characters can be entered. The entry field scrolls
automatically from one line of text to the next. Apart from the SI
module, data can also be entered via the PC keyboard (requires
adapter PROFI-MF-II, article number Z504H).

A comment can be entered for each test procedure in the same
way, immediately after completion of the test. However, the length
of these comments is limited to 15 characters.

5.1.2

Copying Descriptions

➭

Select the system with the description to be copied, and press
the MENU key three times.

➭

Select the new system and press the MENU key.

The copied text appears and can be edited as desired.

5.1.3

Deleting a Description

➭

Simultaneously press the i/STORE and the START keys.

The description is deleted and the cursor jumps to the first entry
position in the respective description entry field.

«
...
41
42
43
44
45
...
»

Summary of Contents for PROFITEST 204













































































Reviews:

No comments