background image

4

Assembly

Handlebar Steer Tube Assembly (Trade Edition)

Tools required: 5mm hex wrench, 10mm wrench

Handlebar Steer Tube Assembly (Luxury)

Tools required: 5mm hex wrench, 10mm wrench

1. Depress the push button located on 

the rear of the fork and insert the 

handlebar steer tube onto the fork. 

The push button should align with the 

locator hole in the handlebar steer 

tube and lock the steer tube securely 

in place.

1.Loosen handbar Latch,as shown in 

fig"A",then,pull up"D"to chute,put 

steem tube from"C"to"B",so that can 

fix steem tube.Same argument,if want 

to folding the steem tube,work The 

above-mentioned steps to 

oppositedirection.

2. Tighten the bolts with the 5mm hex

wrench, evenly and securely.

3. Align handlebars both vertically and

horizontally (a) onto handlebar steer 

tube clamp (b) install handlebar clamp 

and hardware (c&d) and tighten 

evenly and securely with the 5mm hex 

wrench and 10mm wrench.

B

A

2. Align handlebars both vertically and

horizontally (a) onto handlebar steer 

tube clamp (b) install handlebar clamp 

and hardware (c&d) and tighten 

evenly and securely with the 5mm hex 

wrench and 10mm wrench.

D

E

A

C

B

c

d

a

b

Summary of Contents for skitz 2.0


















Reviews: