Gorilla Playsets Sun Palace Deluxe 723 Manual Download Page 78

Page: 78 / 157

ROOF FINISHER

1 X 4 X 55”

CHIMNEY

(FIRST ONE)

ROOF BOARD

1-1/2” WOOD SCREW

(FOURTH ONE)

1 X 6 X 55”

ROOF BOARD

(ONE ON EACH

SIDE OF ROOF)

DORMER

ROOF BOARD

(NINTH ONE)

STEP 38: ROOF

1: PLACE THE 1 X 6 X 55" ROOF BOARDS ON TOP OF THE ROOF SUPPORTS, FITTING THE TONGUE END INTO THE

GROOVE END OF THE ROOF STARTERS. EACH SIDE OF THE ROOF GETS FOURTEEN ROOF BOARDS. THE HOLES IN THE

ROOF BOARDS SHOULD BE CENTERED OVER THE ROOF SUPPORTS. IF NECESSARY PLACE A SCRAP 2 X 4 BOARD

AGAINST THE ROOF BOARD AND HAMMER ON IT TO SEAT THE TONGUE INTO THE GROOVE FOR THE ROOF

BOARDS.
2: FASTEN THE ROOF BOARDS TO THE ROOF SUPPORTS WITH 1-1/2" WOOD SCREWS.
3: PLACE A 1 X 4 X 55" ROOF FINISHER AT THE END OF THE ROOF ASSEMBLY, AND FASTEN WITH 1-1/2" WOOD

SCREWS.
TIP: USE THE INSTRUCTIONS PROVIDED IN THE APENDIX TO BUILD THE CHIMNEY AND DORMERS TO BUILD THEM.

INSTALL FOUR ROOF BOARDS AND THEN INSTALL THE CHIMNEY ACCORDING TO THE CHIMNEY INSTRUCTIONS.

AFTER INSTALLING THE NINTH ROOF BOARD INSTALL THE DORMER ACCORDING TO THE DORMER INSTRUCTIONS.

THEN FINISH INSTALLING THE REMAINING ROOF BOARDS AND ROOF FINISHER. ALSO NOTE THAT THERE IS ONE

DORMER ON EACH SIDE OF THE ROOF.

Summary of Contents for Sun Palace Deluxe 723






























































































































































Search results

Summary of Contents for Sun Palace Deluxe 723

Reviews:

Gorilla Playsets Sun Palace Deluxe 723, Manual, Page: 78 / 157

Search results

Summary of Contents for Sun Palace Deluxe 723

Reviews: