manualshive.com logo in svg

Gorilla Playsets Sun Palace Deluxe 723, Manual, Page: 109 / 157

Share
Download
Gorilla Playsets Sun Palace Deluxe 723 Manual Download Page 109

STEP 3: SANDBOX BOARDS AND TOP PANEL BOARD

YOU WILL NEED AN EXTRA PERSON FOR THIS STEP.
1: WITH HELP, STAND UP THE FRONT AND BACK SIDE ASSEMBLIES.
2: ATTACH ONE 2 X 6 X 58.38" SANDBOX BOARD TO THE BOTTOM OF THE POSTS OF BOTH FRAME ASSEMBLIES ON  

EACH SIDE , THE HOLES IN THE SANDBOX BOARDS MUST BE OFFSET UP. USE 5/16" X 4-1/2" HEX BOLTS AND 5/16" 

WASHERS TO ATTACH THE TOP HOLES OF THE SANDBOX BOARD TO THE T-NUTS INSTALLED ON THE POSTS. THE 

BOTTOM HOLES WILL BE USED LATER.
3: ATTACH THE 2 X 6 X 58.38" TOP PANEL BOARD AT THE TOP OF THE CORNER POSTS OF BOTH FRAME ASSEMBLIES, 

THE HOLES IN THE TOP PANEL BOARD MUST BE OFFSET DOWN. USE 5/16" X 4-1/2" HEX BOLTS AND 5/16" WASHERS 

TO ATTACH THE BOTTOM HOLES OF THE TOP PANEL BOARD TO THE T-NUTS INSTALLED ON THE POSTS. THE TOP 

HOLES WILL BE USED LATER.
4: DO NOT INSTALL ANY LAG SCREWS AT THIS TIME.

SIDE OF FORT

(LOWER LEVEL)

ASSEMBLY

BACK 

2 X 6 X 58.38" 

FRONT 

ASSEMBLY

SANDBOX BOARD

2 X 6 X 58.38" TOP PANEL BOARD

5/16" WASHER

5/16" X 4-1/2" HEX BOLT

5/16" X 4-1/2" HEX BOLT

5/16" WASHER

RIGHT

UPPER LEVEL

LOWER LEVEL

101

Summary of Contents for Sun Palace Deluxe 723






























































































































































Reviews:

No comments