Gorilla Playsets Sun Palace Deluxe 723 Manual Download Page 134

Page: 134 / 157

(SEVENTH ONE)

1 X 6 X 65.38" ROOF BOARD

(FIRST ONE)

DORMER

(ONLY THIS SIDE)

STEP 28: ROOF BOARDS, ROOF FINISHER AND DORMER

ROOF BOARDS

SCREWS.
4: USE THE INSTRUCTIONS PROVIDED WITH THE DORMER TO BUILD IT. AFTER INSTALLING THE SEVENTH ROOF BOARD

INSTALL THE DORMER ACCORDING TO THE DORMER INSTRUCTIONS. THEN FINISH INSTALLING THE REMAINING ROOF

3: PLACE A 1 X 4 X 65.38" ROOF FINISHER ON THE END OF THE ROOF, AND FASTEN USING #8 X 1-1/2" WOOD

THE ROOF SUPPORTS WITH #8 X 1-1/2" WOOD SCREWS.

BOARDS AND ROOF FINISHER.

1: PLACE THE 1 X 6 X 65.38" ROOF BOARDS ON TOP OF THE RIGHT SIDE ROOF SUPPORTS, FITTING THE TONGUE END

INTO THE GROOVE END OF THE ROOF STARTERS. THIS SIDE GETS EIGHT ROOF BOARDS. FASTEN THE ROOF BOARDS

TO THE ROOF SUPPORTS WITH #8 X 1-1/2" WOOD SCREWS.
2: PLACE A 1 X 4 X 65.38" ROOF FINISHER ON THE END OF THE ROOF, AND FASTEN USING #8 X 1-1/2" WOOD

SCREWS.
3: PLACE THE 1 X 6 X 65.38" ROOF BOARDS ON TOP OF THE LEFT SIDE ROOF SUPPORTS, FITTING THE TONGUE END

INTO THE GROOVE END OF THE ROOF STARTERS. THIS SIDE GETS NINE ROOF BOARDS. FASTEN THE ROOF BOARDS TO

ROOF BOARDS

1 X 6 X 65.38" ROOF BOARD

(FIRST ONE)

#8 X 1-1/2" WOOD SCREW

1 X 4 X 65.38" ROOF FINISHER

126

Summary of Contents for Sun Palace Deluxe 723






























































































































































Search results

Summary of Contents for Sun Palace Deluxe 723

Reviews:

Gorilla Playsets Sun Palace Deluxe 723, Manual, Page: 134 / 157

Search results

Summary of Contents for Sun Palace Deluxe 723

Reviews: