Gorilla Playsets Sun Palace Deluxe 723 Manual Download Page 50

Page: 50 / 157

W/SQUARE HOLE

3-1/2" CARRIAGE BOLT

SWING BEAM PLATE

4 X 4 X 120"

SWING BEAM

SIDE RAIL

3/8" LOCK NUT

3/8" WASHER

BOLT CAP

SWING BEAM SIDE RAIL

STEP 11: ATTACHING THE SWING BEAM PLATE TO THE

1: FIND THE 4 X 4 X 120" SWING BEAM SIDE RAIL. NOTE THE DIFFERENCE BETWEEN THE SWING BEAM SIDE RAIL AND

THE SIDE RAIL. THE SWING BEAM SIDE RAIL WILL HAVE THREE MORE COUNTER SUNK HOLES ON ONE SIDE THAN THE

SIDE RAIL.
2: FIND THE SWING BEAM PLATE. NOTICE THE TWO SQUARE HOLES ON THE SWING BEAM PLATE.
3: PLACE THE SWING BEAM PLATE ON TOP OF THE SWING BEAM SIDE RAIL AND LINE UP THE THREE HOLES ON THE

PLATE WITH THE THREE HOLES ON THE SWING BEAM SIDE RAIL. MAKE SURE THE COUNTER-SUNK HOLES ARE ON THE

OPPOSITE SIDE OF THE SWING BEAM PLATE.
4: FASTEN THE SWING BEAM PLATE TO THE SWING BEAM SIDE RAIL WITH TWO 3-1/2" CARRIAGE BOLTS. THE

SQUARE NECK OF THE CARRIAGE BOLT WILL FIT INSIDE THE SQUARE HOLES OF THE SWING BEAM PLATE. NO

WASHER IS NEEDED.
5: FINISH INSTALLING THE SWING BEAM PLATE TO THE SWING BEAM SIDE RAIL WITH 3/8" WASHERS, AND 3/8" LOCK

NUTS. INSTALL BOLT CAPS OVER ANY EXPOSED THREADS.

Summary of Contents for Sun Palace Deluxe 723






























































































































































Search results

Summary of Contents for Sun Palace Deluxe 723

Reviews:

Gorilla Playsets Sun Palace Deluxe 723, Manual, Page: 50 / 157

Search results

Summary of Contents for Sun Palace Deluxe 723

Reviews: