manualshive.com logo in svg

Gorilla Playsets Sun Palace Deluxe 723, Manual, Page: 41 / 157

Share
Download
Gorilla Playsets Sun Palace Deluxe 723 Manual Download Page 41

STEP 2:  ATTACHING THE ROPE LADDER RUNNER

1:  FIND THE 4 X 4 X 97" ROPE LADDER RUNNER.  TAKE SPECIAL NOTE OF THE ROUNDED EDGE ON THE 7/8" HOLES 

ON THE END OF THE ROPE LADDER RUNNER.
2:  LINE UP THE TWO 3/8" PILOT HOLES ON THE ROPE LADDER RUNNER TO THE COUNTER-SUNK HOLES ON THE 

LADDER SIDE PIECES.  THE COUNTERSUNK HOLES OF THE LADDER ASSEMBLY WILL FACE OUTWARDS.
3:  FIND TWO T-NUTS, AND SET WITH A HAMMER ON THE EXPOSED 3/8" HOLES OF THE ROPE LADDER RUNNER.
4:  FASTEN THE ROPE LADDER RUNNER TO THE LADDER ASSEMBLY WITH 5/16 X 6" HEX BOLTS AND 5/16" WASHERS 

THROUGH THE COUNTER-SUNK HOLES OF THE LADDER SIDES AND INTO THE T-NUTS INSTALLED IN THE ROPE LADDER 

RUNNER.  ATTACH THE LADDER CENTER TO THE ROPE LADDER RUNNER USING ONE 3/8" X 5" LAG SCREW AND ONE 

3/8" WASHER.

LADDER 

HEX BOLT

T-NUT

CENTER

ROPE LADDER RUNNER

4 X 4 X 97"

LAG SCREW

3/8" x 5"

3/8" WASHER

ROUNDED EDGE

5/16" WASHER

T-NUT

5/16" X 6"

LADDER SIDES

COUNTERSUNK

HOLE

33

Summary of Contents for Sun Palace Deluxe 723






























































































































































Reviews:

No comments