Gorilla Playsets Sun Palace Deluxe 723 Manual Download Page 63

Page: 63 / 157

4 X 4 X 70"

TIRE SWING SUPPORT

VIEW FROM THE BOTTOM OF THE FORT

3/8" WASHER

SUPPORT BOARD

ROCK WALL

2 X 4 X 58"

THIS BOARD

USE 2" WOOD SCREWS

WHEN INSTALLING

3/8 X 5" LAG SCREW

SEE IMAGE BELOW FOR LOCATION OF THE CENTER

DECK SUPPORT

STEP 23: CENTER DECK SUPPORTS

1: FIND THE 4 X 4 X 70" TIRE SWING SUPPORT, AND ARRANGE EVENLY UNDERNEATH THE DECK.
2: ATTACH THE TIRE SWING SUPPORT WITH A 3/8 X 5" LAG SCREW AND A 3/8" WASHER THROUGH THE LADDER

CENTER. FROM THE TOP, ADD TWO 2-1/2" WOOD SCREWS THROUGH THE DECK BOARDS, INTO THE CENTER DECK

SUPPORT.
3: FIND THE 2 X 4 X 58" ROCK WALL SUPPORT BOARD, AND CENTER IT ON THE BACK OF THE ROCK WALL. MAKE

SURE THAT THE HOLE IN THE BOTTOM ROCK WALL BOARD IS NOT OBSTRUCTED BY THE ROCK WALL SUPPORT

BOARD.
4: THE ROCK WALL SUPPORT BOARD WILL ATTACH TO THE ROCK WALL WITH TWO 2" WOOD SCREWS PER END,

AND AN ADDITIONAL 2" WOOD SCREW IN THE MIDDLE OF THE ROCK WALL SUPPORT BOARD AT EACH ROCK

WALL BOARD. FROM THE FRONT OF THE ROCK WALL, ADD TWO 2" WOOD SCREWS THROUGH THE ROCK WALL

BOARDS, INTO THE ROCK WALL SUPPORT BOARD.

Summary of Contents for Sun Palace Deluxe 723






























































































































































Search results

Summary of Contents for Sun Palace Deluxe 723

Reviews:

Gorilla Playsets Sun Palace Deluxe 723, Manual, Page: 63 / 157

Search results

Summary of Contents for Sun Palace Deluxe 723

Reviews: