Gorenje SIT 2400CGI, Instruction Manual

Page: 19 / 26

19
Check the laundry care label for the required ironing
temperature:
● Synthetic fabrics (e.g. acrylic, nylon, polyester)
ACRYL-NYLON
●● Silk,Wool, , polyamide
SILK-POLY-BLEND-WOOL
●●● Cotton, Jeans
COTTON-JEANS
MAX••• Linen
LINEN
DRY IRONING
Adjust The Variable Steam Control/Self Cleaning
Knob to minimum position " " .
Adjust the Temperature to ‘●’ (1 dot), ‘●●’ (2 dots)
or‘●●●’ (3 dots),
MAX•••
according to the recommendation of garment label.
STEAM IRONING
Make sure that there is enough water in the water
tank. Select the recommended ironing temperature.
Select the appropriate steam setting. Make sure
that the steam setting you select is suitable for the
ironing temperature selected :

for moderate steam select the appropriate steam
settings

for maximum steam
SPRAY FUNCTION
You can use the spray function to remove stubborn
creases at any temperature.
Make sure that there is enough water in the water
tank.
Press the spray button several times to moisten the
article to be ironed.(picture 5)
BURST OF STEAM (picture 6)
A powerful shot of concentrated steam helps
remove stubborn creases.The forward-directed
concentrated shot of steam enhances the
distribution of steam into every part of your
garment.
The shot-of-steam function can only be used at
temperature settings between ●● and MAX.
1
Press and release the shot-of-steam button
.Betwen every shot wait for few seconds.
VERTICAL SHOT OF STEAM
The shot-of-steam function can also be used when
you hold the iron in vertical position.This is useful
for removing creases from hanging clothes, curtains
etc. Hold the iron betwen 15 and 30 centimeters
away from the garment . (picture 7) . Never direct
the steam towards people.
DRIP STOP
This iron is equipped with a drip-stop function: the
iron automatically stops producing steam when the
temperature is too low to prevent water from
dripping out of the soleplate.When this happens you
may hear a sound.
AUTOMATIC ANTI-CALC SYSTEM
The built-in anti-calc system reduces the build-up of
scale and guarantees a longer life for the iron.
ELECTRONIC SAFETY SHUT-OFF
FUNCTION
The electronic safety shut-off function automatically
switches off the iron if it has not been moved for a
while. The red auto-off pilot light »
II
« will flash
indicate that the iron has been switched off by the
safety shut-off function.To let the iron heat up again,
pick up the iron or move it slightly.The red auto-off
pilot light goes out. If the temperature of the
soleplate has dropped below the set ironing
temperature, the temperature pilot light goes on.
SELF CLEANING
This function removes the scales and minerals built
up in the Steam Chamber. The iron will remain in
the best condition if this function is performed at
least once a month or more regularly depending on
the hardness of the water used. Adjust with control
button temperature to ‘●●●’ setting.Pilot light goes
off when the required temperature is reached.
Wait for one more cycle; pilot light glows and goes
off.Adjust the temperature to ‘Min’. Disconnect the
iron from mains supply outlet.
Hold the iron horizontally over a sink. Push and hold
the Self-Cleaning Knob 10 (Descaling) .Steam and
boiling hot water will drain from the holes on the
soleplate washing away the scales and minerals
that have built up inside the Steam Chamber.
Gently move the iron back and forth until the water
tank is empty. When Self-Cleaning is complete,
release the Steam Control/Self-Cleaning Knob.Rest
your steam iron back on its heel rest and allow to
fully cool down.
Wipe the soleplate with a cold damp cloth.
DRAINING THE WATER
Move the Steam Control/Self-Cleaning Knob to
position " " .Disconnect the iron from the mains
supply outlet.Press the Burst Of Steam button to
release any trapped water when the soleplate still
hot. Press the Spray Buttons to release any trapped
water. Hold the iron upside down and gently shake
it to remove the remaining water.