background image

Any time

ON

Any distance (5 - Max.(100 ft.))

SET RANGE KNOB TO

SET MINUTES KNOB TO

SET WALL SWITCH TO

Any time

ON

Any distance (5 - Max.(100 ft.))

SET RANGE KNOB TO

SET MINUTES KNOB TO

SET WALL SWITCH TO

SECURITY LIGHT MODE SETTINGS (High Beam)

TEST mode allows the operator to verify the sensor range is working properly regardless of 

whether it is day or night. TEST allows the internal dusk-to-dawn sensor to be by-passed 

temporarily.

1. To put the light into 

TEST

 mode turn 

Minutes

 control knob to 

TEST

.

2. To exit 

TEST

 mode, rotate the 

Minutes 

control knob away from 

TEST

.

The 

MINUTES

 control determines the length of 

time the lights stay on.When the 

MINUTES

 control 

is set between 1 and 10, the light will only

come on during night time hours. 

NOTE: 

Automatically set at 3 minutes

SETTING THE MOTION DETECTION RANGE: 

240°

100ft.

100ft.

to 

MAX.

 

Fig. 1

45°

MAX.

Fig. 2

The position of the sensor should not exceed 45° below 

horizontal. Do not aim the motion sensor at any water, 

bushes or plants that may move in the wind, pedestrian 

traffic, moving cars, etc., as this may trigger the motion 

sensor. 

(Fig. 2)

DO NOT POSITION THE SENSOR WITH THE 

CONTROLS FACING UPWARD.

USING MANUAL OVERRIDE

ON

OFF

ON

OFF

ON

OFF

ON

OFF

2 Seconds

SETTING THE LIGHT MANUAL OVERRIDE: 

If the security light has been turned off at the switch, turn it on for 20 seconds to 

allow the (PIR) sensor time to warm up prior to initiating the manual override 

sequence.
To switch over to manual mode, switch the power 

ON-OFF-ON

 within 2 seconds. 

There are 2 ways to return to sensor control:
1) To  immediately switch out of manual mode, repeat the manual mode sequence of 

 power 

ON-OFF-ON

 within 2 seconds. This will cancel out manual mode.

2) The security light will remain on until the internal dusk-to-dawn sensor detects 

  the next dusk-dawn cycle. Once light is detected, it will allow the motion sensor to

  return to controlling the fixture the next day.  

MANUAL OVERRIDE

 allows the light to turn on at any time, by 

overriding all sensor controls, so the light comes on regardless of time 

of day.

Initial state

on for 20 sec. 

warm up sensor

SETTING THE LIGHT ACTIVATION TIME:

Rotate the 

MINUTES

 control knob clockwise to control the length of time the lights will remain on. The 

time settings of  

1’ (1 min.)

2’(2 min.)

5’ (5 min.)

10’ (10 min)

 are marked. However, the 

MINUTES

 

control knob can be set anywhere from 

1 minute

 up to 

10 minutes

. The time length can be set up or 

down.

MOTION SENSOR 

The 240-degree coverage of the motion sensor is measured side-to-side. 

The sensor is more effective side-to-side, rather than motion coming 

straight at it (in-and-out). Adjust the motion sensor head so that it detects 

motion moving across the coverage area.  

Rotate the 

RANGE

 control knob anywhere from 

5 Ft 

 to 

MAX.

 

(100 ft).

 When the 

RANGE

 control knob is turned to 

5 Ft

, the 

detection zone is very tight and compact, causing the detection 

sensitivity to be very high. The reverse is true, when the 

RANGE

 

control knob is turned to 

MAX

, the detection zone increases 

exponentially with sensitivity being low. Perform a “walk by test” by 

walking across the motion detection field at the approximate 

distance set on the 

RANGE

 control knob 

(Fig. 1)

 .

 IF THE TEST 

FAILS

, try adjusting the sensor head toward the detection zone. 

Sensor head can be adjusted either up or down, or left or right. 

NOTE:

 If the sensor arm becomes loose, readjust the 

sensor head and tighten the joint screw on the sensor 

arm.

Good Earth Lighting

®

 - 10 YEAR LIMITED WARRANTY:

 

The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of (10) years from the date of original 

purchase by the consumer. The fixture is not warrantied for use in a commercial or retail application.  The warranty is limited to use in a residential 

environment. We will repair or replace (at our option) the unit in the original color and style if available, or in a similar color and style if the original item has 

been discontinued, without charge. Defective units must be properly packed and returned to the manufacturer with a letter of explanation and your original 

purchase receipt showing date of purchase. Call 

1-800-291-8838 

to obtain a return authorization number and an address where to ship your defective 

product. 

Note:

 C.O.D. shipments will 

NOT

 be accepted. The liability of the manufacturer is in any case limited to replacement of the defective light fixture 

product. The manufacturer will not be liable for any other loss, damage, labor costs or injury which is caused by the product. This limitation upon the liability 

of the manufacturer includes any loss, damage, labor costs or injury which is (I) to person or property or otherwise; (II) incidental or consequential in nature; 

(III) based upon theories of warranty, contract, negligence, strict liability, tort, or otherwise; or (IV) directly, or indirectly related to the sale, use, or repair of 

the product. This warranty gives you specific rights, and you may also have other rights which vary from state to state.

FCC STATEMENT:

 

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device 

must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by 

the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a 

Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. 

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to 

radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio 

or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following 

measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a circuit 

different from that of the receiver. 4) Consult the dealer or an experienced radio/TV technician for help.

REPLACEMENT PARTS LIST: 

Hardware Kit: ZH-SE1292F02

FCC responsible party name :

 Good Earth Lighting, Inc. 

Address: 

1400 E Business Center Drive, STE 108, Mount Prospect IL 60056, USA 

Telephone number:

 1-800-291-8838

3

El modo de TEST permite al operador verificar que el alcance del sensor está funcionando 

correctamente, independientemente de si es de día o de noche. TEST permite que el sensor 

interno de anochecer a amanecer sea rodeado temporalmente.

1.  Para poner la luz en el modo de 

TEST

, gire el botón giratorio de control del temporizador 

TIMER

    

 hasta 

TEST

.

2.  Para salir del modo de 

TEST

, rote el botón giratorio de control de la sensibilidad 

RANGE 

de  

 

  manera que se aleje de 

TEST

.

10

Summary of Contents for SE1292-BP2-02LF0-G













Reviews: