UK2AAA eLED MPL I - AN
US
Features
• High-intensity 1-watt white LED lasts thousands
of hours without burning out
• Thermal Recovery System transfers heat
from LED to warm batteries for better cold
weather performance
• Twist ON/OFF front bezel switch
• Extra strong pocket clip
• Passes 6 foot drop test
• Watertight and dustproof up to 10 feet water depth
• Corrosion and impact resistant case
• Conforms to UL 783, 913 and ISA 12.12.01
for hazardous location usage
Battery Installation
Unscrew the black bezel which contains the eLED module. It is one unit and should
not be taken apart. Insert 2 alkaline AAA-size batteries into the case as shown to
the left.
NOTE: The batteries must be inserted with the plus + end facing the reflector for
the LED module to light. Make sure the O-ring and sealing surfaces are clean.
Replace the bezel/eLED module by screwing it down over the o-ring.
ON/OFF
Screw the bezel down by twisting it clockwise until the lamp comes ON. Turn the
light OFF with at least 1 1/2 turns counterclockwise of the bezel.
O-Ring Seal
The O-ring and threads must always be kept clean. Lightly lubricate the O-ring
which seals the rubber covered bezel and case with silicone grease. Remove the
O-ring by hand. Do not use tools.
Care and Maintenance
• Keep area around the 0-ring clean.
• If the light floods, empty it immediately, rinse with fresh water and dry completely
before reassembly.
• Replace the bezel / lamp module, which contains a hydrogen absorbing catalyst
, if it gets wet.
• Do not store batteries in the light for long periods of time when not in use; they
may leak and damage the light.
PN 401389
Operating Instructions and Important Information
UK2AAA eLED MPL I - AN
WARRANTY
Underwater Kinetics products are engineered for maximum performance and durability. All products carry a
Limited Lifetime Warranty to the original retail purchaser to be free from defective material and workmanship under
normal and intended use. In addition, the Underwater Kinetics Limited Warranty covers materials used in its products
to the original purchaser, from the date of purchase, as follows: plastics for 10 years; rubber for 3 years, LED and
electronics for 1 year, rechargeable batteries for 90 days.
In the event the original retail purchaser detects a defect in the material or workmanship, the product along with
proof of purchase date should be returned to an authorized Underwater Kinetics dealer or directly to Underwater
Kinetics with the postage prepaid. Underwater Kinetics agrees to repair or replace at Underwater Kinetics' sole
discretion any product found to be defective in material or workmanship within the time period specified above. For
the complete Limited Lifetime Warranty write to Underwater Kinetics or go to the web site www.uwkinetics.com.
Address all correspondence and returns to:
Underwater Kinetics, 13400 Danielson Street, Poway, CA 92064 or email [email protected]
Congratulations on the purchase of your Underwater Kinetics all environment work light. The
UK2AAA eLED MPL I light is tough enough for use in rain, snow, smoke, dust or hazardous locations
(see listing.)
Technical Data UK2AAA eLED MPL I -AN
batteries: 2 AAA/LR03 alkaline batteries
lamp type: high-intensity LED
test depth: 10(3) ft(m)
beam travel: 211(64) ft (m)
size: 3.2(81) x 1.10(28) x 0.87(22) in (mm)
weight: 1.7 (48) oz (g) (incl. batteries)
materials: ABS, Polycarbonate, TPU Rubber,
Copper
WARNING
To reduce the risk of explosion, do not mix old batteries with used
batteries, or mix batteries from different manufacturers
WARNING
Substitution of components may impair intrinsic safety.
WARNING
To reduce risk of a flammable or explosive atmosphere, batteries must be
changed only in a location known to be non-hazardous.
WARNING
Batteries can vent hydrogen gas and possibly cause an explosion (1) if
they are installed without the proper polarity, (2) if they are not the same
type, brand name and age or (3) if they are completely discharged.
• Load batteries according to the diagram.
• Discard all batteries as soon as they are drained or no longer produce
light.
• Do not mix batteries of different type, brand or age.
CL I,II, III DIV 1 GROUP A-G, T4 Exia
CONFORMS TO UL STD 783, UL STD
913, AND CERTIFIED TO CSA STD
C22.2 No. 157.
3188451
CERTIFICATION INFORMATION
UK2AAA eLED MPL I -AN
1. Read the instructions before use.
2. Do not open in hazardous locations.
3. Use only Part No. 13807 Bezel/LED Assembly.
4. Use only DURACELL MN2400, ENERGIZER
EN92, or RAYOVAC 824 AA/LR6 alkaline batteries
5. Manufactured by
Underwater Kinetics, 13400 Danielson Street
Poway, CA 92064 USA
tel (858) 513-9100; fax (858) 513-9111
13807
Bezel/LED
Assembly
2 AAA
Alkaline
Batteries
Hat Clip
Battery Installation
O-Ring
Case &
Key Ring
