background image

75

O

To make a call the visitor should press the push button corresponding to the apartment he wishes to

contact. An acoustic tone will be heard confirming the call is in progress once the push button has

been pressed

. At this moment the call will be received at the

and the door panel led will turn on

monitor (telephone) in the dwelling. During the call the visitor can correct his call by pressing a push

button corresponding to a different apartment, in which case the original call is cancelled.

O

In systems with several accesses doors, the other(s) door panel(s) will be automatically disconnected:

If a visitor tries to call from other door panel an acoustic tone will be heard and the door panel

led   will be on

.

confirming the system is busy

O

General door panel (EL501 mode): If the call is made from the general door panel, the inner door

panel of the building called and other possible general door panel will remain automatically

disconnected, if another visitor tries to call from an inner busy door panel an acoustic tone will be

heard

confirming the system is busy or from another general door

and the door panel led will be on

panel, an acoustic tone will be

confirming the system is busy and

heard

the general door panel led

will blink for 3 seconds. The door panels of the others inner buildings will remain free to be used.

O

General door panel (EL501 mode): In the case that the call is made from an inner door panel, the rest

of inner door panels will remain free to be used. From general door panels only will be able to make

calls to the inner buildings whose door panels are not in use, if the visitor tries to make a call to a busy

inner door panel, an acoustic tone will be heard confirming the system is busy and the general door

panel

will blink for 3 seconds

led

.

O

The call lasts for 45 seconds, during which time an image appears on the apartment's monitors for 2

seconds after the call is received without the visitor knowing, and the status LED on the master monitor

will illuminate (green). If the call is not answered within 45 seconds, the master monitor's status LED

will illuminate (red), LED on the door panel will turn off and the channel will be free.

O

To establish communication, lift the handset of the monitor (telephone), and the monitor's status LED

(green) and the door panel's LED will illuminate

.

O

The communication will last for one and a half minutes or until the handset is replaced. After the

communication, the monitor's status LED will illuminate (red), the door panel's LED will turn off and

the channel will be free.

O

To open the door, press the door release push button during call or communication progresses: with

one press, the door release operates during 3 seconds. During the lock release activation an acoustic

tone will be heard on the door panel confirming the lock release is activated and the led

will also

turn on for 3 seconds.

SYSTEM OPERATION

76

DOOR PANEL DESCRIPTION

Sound module

EL63 Plus P/T

2

EL64 Plus

2

D

oor panel description.

Push buttons electronic module

EL610D

Short connection cable, It is supplied with EL610D module (16 cm length).

, for 5 single push-buttons or 10 double push buttons.

, on video systems with color camera.
, on audio systems.

Connection cable RAP-610D (27 cm length).

General detail of parts, for assembly the door panel.

Aluminium modules

Electronic

modules

Frame modules

Embedding boxes

Push buttons module

Main module

Door panel description.

For the connection of the push-buttons between the sound module and the push

buttons module EL610D and between push-buttons modules EL610D.

For the connection of the push-buttons between the sound module and the push

buttons module EL610D and between push-buttons modules EL610D.

This cable is necessary when the distance between modules to connecting is

greater due to the distribution of these modules in the door panel/s.

Bus Nexa connection cable e th

(l ng 50 cm).

For the connection of the

or

modules with others Bus

EL632 Plus P/T

EL642 Plus

Nexa modules (see page

).

83

Uno system:

O

Tekna Uno monitor

T-540 Uno telephone are fully compatible with Tekna Plus monitor

T-

and

and

540 Plus telephone. However,

a Uno communications resistor must be setting with the

SW1 configuration dip switch of the door panel,

see

85 .

(

page

)

O

If the distance from the door panel to the farest monitor or telephone is longer than 200 meters, or
the building has more than 200 apartment units, a

repeater must be installed.

RDPlus/Uno SE

IMPORTANT NOTICE

IMPORTANT NOTICE

Summary of Contents for Plus Nexa









































Reviews: