85
D
escription of the SW1 configuration dip-switch of
the sound module.
Placed to OFF if the sound module is configured as EL500
.
operating mode
Set to ON if the sound module is configured as EL501 operating mode
(general door panel).
Selects the d
done from the
( AP
' '
oor opening time,
external push button
terminal), see page 106.
Placed to ON: door opening timed at 3 seconds.
Set to OFF: door opening timed at 15 seconds.
Selects the type of cable to be used for the video signal.
Placed to OFF: coaxial cable RG-59 o RG-11.
Set to ON: twisted pair.
Placed to OFF if the door panel has telecamera. In case of door panels
without telecamera (EL642 Plus sound module) set to ON.
Plus system
, loads the installation with a communications resistor
. For a
Plus
proper system operation, placed to ON only in the closest door panel to the
backbone installation or in the general door panel (if exists), set the rest to
OFF.
Set to ON so that the volume tone emitted by the door panel:
(call reception, busy system and lock release) are
or placed to OFF if a
HIGH,
LOW
volume tone is desired.
Uno System
, loads the installation with a communications resistor
. For a
Uno
proper system operation, set to ON only in the closest door panel to the
backbone installation, placed the rest to OFF.
With digital repeater RD Plus/Uno:
In the backbone installation or after the inner door panel in systems with
general door panels, placed the door panel/s to OFF.
6
6
7
6
7
6
Placed to ON, the calls made on the door panel will be transferred to the
porter's exchange (if exists)
. Set to OFF, the call is received in the apartment.
In general door panels systems with porter
, this function is only
's exchange
applicable to the general door panels not to the inner door panel/s.
Factory default
The SW1 configuration dip-switch is located at the upper right
side of the back of the module.
Not :
e
9
10
The dip-switches and
without function.
DOOR PANEL INSTALLATION
6
7
8
6
7
8
86
DOOR PANEL INSTALLATION
B
inary coding of the SW2 configuration dip switch of
the sound module.
The switches set to OFF have null value. The values of the switches
set to ON are shown in the enclosed chart.
The backbone code will be calculated as the sum result of the
switches values set to ON.
Example: 64+0+16+0+4+2+1=87
Switch number:
ON value:
4
64
5
32
6
16
7
8
8
4
9
2
10
1
D
escription of the SW2 configuration dip-switch of
the sound module.
Allows to activate the autoswitch-on function (audio-video communication
without previous call) at the door panel that has this switch to ON position.
In systems with several door panels activate this function only in one of
them; in systems with general door panel this function can be activated in
one door panel of each inner backbone (building).
Set to ON for monitor or telephones programming. Once the programming
progress is finished return the switch to OFF position. The programming
process is described on corresponding monitor / telephone manual, (see
page 74 for manual web link).
In general door panel (EL501 mode), set to ON for general door panel
push buttons programming or backbone (building) monitor/telephones.
The programming process is described on pages 87 to 89. Once the
programming progress is finished return the switch to OFF position.
Set to OFF in case of a master door panel. Each system must have only one
master door panel; the rest must be slaves (ON).
In systems with general door panel, set as master one door panel of each
inner backbone (building) and the general door panel as slave. Of this
way, the user will be able to distinguish since door panel are calling him.
Switches number 4 to 10 set the building code. In backbones with several
door panels, set the same code in all the panels; in systems with general
door panel, set different codes for each inner backbone (building). Set a
code between 1 and 120 for inner backbones (up to 127 with coded
panel) and a code 0 (
) for general door panel/s. To set the
Factory default
code use binary coding as shown on the next paragraph.
Factory default
The SW2 configuration dip-switch is located at the upper left
side of the back of the module.
