manualshive.com logo in svg

GMC SIERRA DENALI 2002, Manual

Share
Download
GMC SIERRA DENALI 2002 Manual Download Page 263

5-21

A. Hoist Assembly

B. Wheel Wrench

C. Extensions

D. Hoist Shaft

E. Valve Stem, 

Pointed Down

F. Spare Tire

G. Tire Retainer

H. Hoist Cable

I. Hoist Lock

J. Hoist Shaft 

Access Hole

K. Hoist End

Follow these instructions to lower the spare tire:

1. Your vehicle is equipped with a hoist lock. Open the

spare tire lock cover on the bumper and use the
ignition key to remove the lock.

2. Assemble the wheel wrench and the two jack handle

extensions as shown. Insert the hoist end (open end)
of the extension through the hole in the rear bumper.
Be sure the hoist end of the extension connects into
the hoist shaft.

3. Turn the wheel wrench counterclockwise to lower

the spare tire to the ground. Continue to turn the
wheel wrench until the spare tire can be pulled out
from under the vehicle. The wheel wrench has a
hook that allows you to pull the hoist cable towards
you, to assist in reaching the spare tire.

4. When the tire has been lowered, tilt the retainer at

the end of the cable so it can be pulled up through
the wheel opening.

5. Put the spare tire near the flat tire.

Summary of Contents for SIERRA DENALI 2002











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands