manualshive.com logo in svg

GMC SIERRA DENALI 2002, Manual

Share
Download
GMC SIERRA DENALI 2002 Manual Download Page 255

5-13

CAUTION:

Heater and radiator hoses, and other engine
parts, can be very hot. Don’t touch them. If you
do, you can be burned.

Don’t run the engine if there is a leak. If you run
the engine, it could lose all coolant. That could
cause an engine fire, and you could be burned.
Get any leak fixed before you drive the vehicle.

If there seems to be no leak, start the engine again. 
The engine cooling fan speed should increase when 
idle speed is doubled by pushing the accelerator pedal
down. If it doesn’t, your vehicle needs service. Turn off
the engine.

NOTICE:

Engine damage from running your engine
without coolant isn’t covered by your warranty.
See “Overheated Engine Protection Operating
Mode” in the Index for information on driving to
a safe place in an emergency.

NOTICE:

When adding coolant, it is important that you use
only DEX

-

COOL

R

 (silicate

-

free) coolant.

If coolant other than DEX

-

COOL is added to the

system, premature engine, heater core or
radiator corrosion may result. In addition, the
engine coolant will require change sooner 

--

 at

30,000 miles (50 000 km) or 24 months,
whichever occurs first. Damage caused by the use
of coolant other than DEX

-

COOL

R

 is not

covered by your new vehicle warranty.

Summary of Contents for SIERRA DENALI 2002











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands