manualshive.com logo in svg

GMC SIERRA DENALI 2002, Manual

Share
Download
GMC SIERRA DENALI 2002 Manual Download Page 168

3-9

AM-FM Stereo with Cassette Tape Player
and Automatic Tone Control

Playing the Radio

PWR (Power): Press this knob to turn the system on
and off.

VOL (Volume): Turn this knob clockwise to increase
volume. Turn it counterclockwise to decrease volume.
The knob is capable of being turned continuously.

RECALL: Pressing this button will display the station
being played or it will display the clock. Clock display
is available with the ignition turned off.

SCV (Speed

-

Compensated Volume): With SCV, your

audio system adjusts automatically to make up for road
and wind noise as you drive. Set the volume at the
desired level. Turn the control ring behind the upper
knob clockwise to adjust the SCV. Each notch on the
control ring allows for more volume compensation at
faster vehicle speeds. Then, as you drive, SCV
automatically increases the volume, as necessary, to
overcome noise at any speed. The volume level should
always sound the same to you as you drive. If you don’t
want to use SCV, turn the control all the way down.

Finding a Station

AM FM: Press this button to switch between AM, FM1
and FM2. The display will show your selection.

TUNE: Press this knob lightly so it extends. Turn it to
choose radio stations. Push the knob back into its stored
position when you’re not using it.

Summary of Contents for SIERRA DENALI 2002











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands