manualshive.com logo in svg

GMC SIERRA DENALI 2002, Manual

Share
Download
GMC SIERRA DENALI 2002 Manual Download Page 136

2-63

Speedometer and Odometer

Your speedometer lets you see your speed in both 
miles per hour (mph) and kilometers per hour (km/h).
Your odometer shows how far your vehicle has been
driven, in either miles (used in the United States) or
kilometers (used in Canada).

Trip Odometer

The trip odometer can tell you how far your vehicle has
been driven since you last set the trip odometer to zero.

Press the reset button, located on the instrument panel
cluster next to the trip odometer display, to toggle
between the trip odometer and the regular odometer.
Holding the reset button for two seconds while the trip
odometer is displayed will reset it.

To display the odometer reading with the ignition off,
press the reset button.

Engine Hour Meter Display

The odometer can also display the number of hours 
the engine has run. To display the hour meter, turn the
ignition off, press and hold the reset button for at least
four seconds. The hour meter will be displayed for up to
30 seconds, or until the ignition is turned on.

Tachometer

Your tachometer displays the engine speed in
revolutions per minute (rpm).

NOTICE:

Damage to your engine or vehicle caused by
operating the engine in the red area isn’t covered
by your vehicle warranty. Don’t operate the
engine with the tachometer in the red area.

Summary of Contents for SIERRA DENALI 2002











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands