GMC 2000 Jimmy Page 250 Owner'S Manual Download | Manualshive

Page: 250 / 430

background image

4-49

Your vehicle may be able to tow a trailer. To identify
what the vehicle trailering capacity is for your vehicle,
you should read the information in “Weight of the
Trailer” that appears later in this section.

If yours was built with trailering options, as many are,
it’s ready for heavier trailers. But trailering is different
than just driving your vehicle by itself. Trailering means
changes in handling, durability and fuel economy.
Successful, safe trailering takes correct equipment, and
it has to be used properly.

That’s the reason for this part. In it are many
time

-

tested, important trailering tips and safety rules.

Many of these are important for your safety and that of
your passengers. So please read this section carefully
before you pull a trailer.

If You Do Decide To Pull A Trailer

If you do, here are some important points:
D There are many different laws, including speed limit

restrictions, having to do with trailering. Make sure
your rig will be legal, not only where you live but
also where you’ll be driving. A good source for this
information can be state or provincial police.

D Consider using a sway control if your trailer will

weigh 2,000 lbs. (900 kg) or less.

You should always use a sway control if your trailer
will weigh more than 2,000 lbs. (900 kg). You can
ask a hitch dealer about sway controls.

D Don’t tow a trailer at all during the first 500 miles

(800 km) your new vehicle is driven. Your engine,
axle or other parts could be damaged.

D Then, during the first 500 miles (800 km) that you

tow a trailer, don’t drive over 50 mph (80 km/h) and
don’t make starts at full throttle. This helps your
engine and other parts of your vehicle wear in at the
heavier loads.

D If you have an automatic transmission, you can use

THIRD (3) (or, as you need to, a lower gear) when
towing a trailer. Operating your vehicle in THIRD (3)
when towing a trailer will minimize heat buildup and
extend the life of your transmission. If you have a
manual transmission and you are towing a trailer, it’s
better not to use FIFTH (5) gear. Just drive in
FOURTH (4) gear (or, as you need to, a lower gear).
See “Tow/Haul Mode” in the Index.

Three important considerations have to do with weight:
D the weight of the trailer,
D the weight of the trailer tongue
D and the weight on your vehicle’s tires.

«
...
248
249
250
251
252
...
»

Summary of Contents for 2000 Jimmy















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2000 Jimmy

Brand: iDataLink Pages: 9

Brand: Ecco Pages: 9

Brand: Ecco Pages: 9

Brand: TATA Motors Pages: 164

Transit Vancouver Wagon

Brand: Webasto Pages: 44

Chevrolet Silverado 2500HD 2021

Brand: GMC Pages: 433

Brand: tams elektronik Pages: 44

Brand: ULTIMATE SPEED Pages: 50

Brand: Mercedes-Benz Pages: 91

Brand: Lund Pages: 12

Brand: Blue Ox Pages: 5

Brand: Nos Pages: 22

LockNLoad LightenUp

Brand: Yakima Pages: 13

Brand: ULTIMATE SPEED Pages: 56

Camry Hybrid 2012

Brand: Toyota Pages: 62

Brand: Ford Pages: 292

Brand: Chevrolet Pages: 88

$T-Rex TEX-51127 Installation Manual preview$

Brand: T-Rex Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands