GMC 2000 Jimmy Page 178 Owner'S Manual Download | Manualshive

Page: 178 / 430

background image

3-21

RECALL: Display the time with the ignition off by
pressing this button. When the radio is playing, press
this button to recall the station frequency.

SCV: Your system has a feature called
Speed

-

Compensated Volume (SCV). With SCV, your

audio system adjusts automatically to make up for road
and wind noise as you drive. Set the volume at the
desired level. Turn the control ring behind the upper
knob clockwise to adjust the SCV. Then, as you drive,
SCV automatically increases the volume, as necessary,
to overcome noise at any particular speed. The volume
level should always sound the same to you as you drive.
If you don’t want to use SCV, turn the control all the
way down. Each notch on the control ring allows for
more volume compensation at faster vehicle speeds.

Finding a Station

AM

-

FM: Press this button to switch between AM, FM1

and FM2. The display will show your selection.

TUNE: Press this knob lightly so it extends. Turn it to
choose radio stations. Push the knob back into its stored
position when you’re not using it.

SEEK: Press the right arrow to tune to the next
higher station and the left arrow to tune to the next
lower station and stay there. The sound will mute
while seeking.

SCAN: Press and hold SEEK for two seconds until
SCAN appears on the display. SCAN allows you to
listen to stations for a few seconds. The receiver will
continue to scan and momentarily stop at each station
until you press the button again. The sound will mute
while scanning.

PUSHBUTTONS: The six numbered pushbuttons let
you return to your favorite stations. You can set up to
18 stations (six AM, six FM1 and six FM2). Just:

1. Turn the radio on.

2. Press AM

-

FM to select the band.

3. Tune in the desired station.

4. Press and hold one of the six pushbuttons. The sound

will mute. When it returns, release the button.
Whenever you press that numbered button, the
station you set will return.

5. Repeat the steps for each pushbutton.

«
...
176
177
178
179
180
...
»

Summary of Contents for 2000 Jimmy















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2000 Jimmy

Brand: N-Com Pages: 28

Brand: Samsung Pages: 133

SmartDiag2GO GD201-O

Brand: OCTO Pages: 5

Brand: Opel Pages: 254

Brand: Honda Pages: 4

SAFESTOP SS0005

Brand: Pro-gard Pages: 4

Brand: GMC Pages: 120

Brand: Prime Tech Pages: 6

OCTAVIA - TECHNICAL CHANGES 11-2009

Brand: Skoda Pages: 16

Brand: Thule Pages: 12

Brand: ORA Pages: 7

Brand: Edelbrock Pages: 2

Brand: Arrista Pages: 2

2010 Accord Coupe

Brand: Honda Pages: 410

Brand: Skoda Pages: 276

Brand: Chevrolet Pages: 103

Brand: Peak Pages: 8

Brand: Renault Pages: 239

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands