GMC 2000 Jimmy Page 171 Owner'S Manual Download | Manualshive

Page: 171 / 430

background image

3-14

In addition to the four stations already set, up to three
more stations may be preset on each band by pressing
two adjoining buttons at the same time. Just:

1. Tune in the desired station.

2. Press SET. (SET will appear on the display.)

3. Press two adjoining buttons at the same time, within

five seconds. Whenever you press the same two
buttons, the station you set will return.

4. Repeat the steps for each pair of pushbuttons.

P.SCAN: Select either AM, FM1 or FM2 mode and
press both SEEK buttons to scan through each of your
preset stations. The system will scan through and play
each preset station stored on your pushbuttons for a few
seconds. Press either SEEK button or RECALL to stop
scanning through the preset stations.

Setting the Tone

BASS: Slide this lever up or down to increase or
decrease bass.

TREB: Slide this lever up or down to increase or
decrease treble. If a station is weak or noisy, you may
want to decrease the treble.

Adjusting the Speakers

BAL: Turn the control behind the upper knob to move
the sound to the left or right speakers. The middle
position balances the sound between the speakers.

FADE: Turn the control behind the lower knob to move
the sound to the front or rear speakers. The middle
position balances the sound between the speakers.

Playing a Cassette Tape

Your tape player is built to work best with tapes that are
up to 30 to 45 minutes long on each side. Tapes longer
than that are so thin they may not work well in this player.

Once the tape is playing, use the knobs for VOLUME,
BAL, FADE, BASS and TREB just as you do for
the radio.

REV: Press the SEEK left arrow to reverse the cassette
tape. Press the SEEK right arrow to stop reversing
the tape.

FWD: Press the SEEK right arrow to advance the
cassette tape. Press the SEEK left arrow to stop
forwarding the tape.

RECALL: Press this knob to switch tape sides.

EJECT: Press this button to remove the tape or stop the
tape and play the radio.

«
...
169
170
171
172
173
...
»

Summary of Contents for 2000 Jimmy















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2000 Jimmy

Brand: Hama Pages: 2

MARTEN-FREE CAR

Brand: Gardigo Pages: 36

Brand: 3SIXT Pages: 12

Wallbox eM4 Single

Brand: ABL Pages: 68

Brand: Brodit Pages: 2

Brand: Power Fist Pages: 12

Brand: EAL Pages: 7

Brand: Unex Pages: 30

Brand: BrandMotion Pages: 6

Brand: POOL-LINE Pages: 2

A-18 TRAILER ABS

Brand: BENDIX Pages: 40

Brand: Toyota Pages: 56

Escalade 2004 Escalade ESV

Brand: Cadillac Pages: 472

Brand: Subaru Pages: 16

Brand: AUTOTECH Pages: 4

Brand: Revelation Pages: 4

BLADE-AL-HK4-EN

Brand: iDataLink Pages: 35

Brand: JBA Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands