GMC 2000 Jimmy Page 183 Owner'S Manual Download | Manualshive

Page: 183 / 430

background image

3-26

SCAN: Press and hold SEEK for two seconds until
SCAN appears on the display. SCAN allows you to
listen to stations for a few seconds. The receiver will
continue to scan and momentarily stop at each station
until you press the button again. The sound will mute
while scanning.

PUSHBUTTONS: The six numbered pushbuttons let
you return to your favorite stations. You can set up to
18 stations (six AM, six FM1 and six FM2). Just:

1. Turn the radio on.

2. Press AM

-

FM to select the band.

3. Tune in the desired station.

4. Press AUTO TONE to select the setting you prefer.

5. Press and hold one of the six pushbuttons. The sound

will mute. When it returns, release the button.
Whenever you press that numbered button, the
station you set will return and the tone you selected
will be automatically selected for that button.

6. Repeat the steps for each pushbutton.

P.SCAN: The preset scan button lets you scan through
your favorite stations stored on your pushbuttons. Select
either the AM, FM1 or FM2 mode and then press
P.SCAN. It will scan through each station stored on your
pushbuttons and stop for a few seconds before continuing
to scan through all of the pushbuttons. Press P.SCAN
again or one of the pushbuttons to stop scanning to listen
to a specific stored station. P.SCAN will light up on the
display while in this mode. If one of the stations stored on
a pushbutton is too weak for the location you are in, the
radio display will show the channel number (P1

-

P6) for

several seconds before advancing to the next preset station.

Setting the Tone

BASS: Press lightly on this knob to release it from its
stored position. Turn the knob clockwise to increase bass
and counterclockwise to decrease bass. When the BASS
control is rotated, the AUTO TONE display will go blank.

TREB: Press lightly on this knob to release it from its
stored position. Turn the knob clockwise to increase
treble and counterclockwise to decrease treble. When
the TREB control is rotated, the AUTO TONE display
will go blank. If a station is weak or noisy, you may
want to decrease the treble.

Push these knobs back into their stored positions when
you’re not using them.

«
...
181
182
183
184
185
...
»

Summary of Contents for 2000 Jimmy















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2000 Jimmy

Brand: U.S. General Pages: 5

Brand: Yakima Pages: 11

Brand: Porsche Pages: 51

Brand: Whispbar Pages: 14

Brand: EUFAB Pages: 52

Road Ready Seat Protector

Brand: Wagan Pages: 12

Brand: Chevrolet Pages: 50

Brand: Kargo Master Pages: 19

PRIME DESIGN VBR3-FT31B

Brand: Safe Fleet Pages: 12

Brand: Saab Pages: 9

Brand: PEUGEOT Pages: 404

Brand: Chevrolet Pages: 88

Brand: Mahindra Pages: 247

2013 Civic Sedan

Brand: Honda Pages: 368

Brand: LAS Pages: 9

Brand: Sune Technology Pages: 20

Brand: SSANGYONG Pages: 931

JAGUAR 2008 - XF

Brand: KAP Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands