background image

32

33

Note:

The measuring cell of an unused test strip 

is transparent. After a sufficient amount of 

blood has been drawn in, the measuring cell 

is filled completely with blood.

The measuring cell of the test strip can only 

be filled at the “nose”, mentioned above. 

Wetting at other places on the test strip won’t 

lead to a correct measurement.

Step 2: 

Once the measuring cell of the test strip 

is sufficiently filled with blood, the meter 

confirms this with a beep. The measurement 

starts automatically.

Step 3: 

The blood glucose measurement takes ten 

seconds. There is a measuring time “count-

down” on the display.

Step 4: 

The end of measurement is confirmed 

with two short beeps. The measured blood 

glucose value is displayed with the date and 

time of the measurement. This data is stored 

in the measured value memory of the user.

Attention:

Hyperglycaemia warning 

(blood glucose level too high):

If the result of your blood glucose measure-

ment is above a level of 160 mg/dl  

(or 8.8 mmol/l), the word “high” appears  

on the right next to the blood glucose value. 

This is a warning that your blood glucose 

level is too high.

Hypoglycaemia warning 

(blood glucose level too low):

If the result of your blood glucose measure-

ment is above a level of 50 mg/dl  

(or 2.78 mmol/l), the word “low” appears  

on the right next to the blood glucose value. 

This is a warning that your blood glucose 

level is too low.

mem

gluco-comfort

biocomfort

mem

mem

gluco-comfort

biocomfort

mem

���

�������������

����������

���

���

�������������

����������

���

����

�����

���

�����

mem

gluco-comfort

biocomfort

mem

���

�������������

����������

���

���

�������������

����������

���

����

�����

���

�����

���

�������������

����������

���

���

�������������

����������

���

����

�����

���

�����

C

ar

ry

in

g o

ut t

he b

lo

od g

lu

co

se m

ea

su

re

m

en

t

3

Summary of Contents for BGM 105





























Reviews: