manualshive.com logo in svg

GLP KNV Dot, Quick Start And Safety Manual

Share
Download
GLP KNV Dot Quick Start And Safety Manual Download Page 9

German Light Products® 

 

 

KNV Dot and Line Quick Start and Safety Manual Rev. A 

9 

 

 

Strobe safety 

•

 

Flashing light, particularly at 5 - 30 Hz, may cause seizures in persons with 
photosensitive epilepsy. Do not use strobe effects for extended periods. 

•

 

Comply with local regulations on the use of strobe lighting and notify the public in 
advance with highly visible warning signs when strobe effects are used. 

•

 

If a seizure occurs, stop using strobe effects. Seek professional medical help. Note 
the time that the seizure starts and finishes. Call emergency medical help urgently if 
the seizure lasts more than five minutes, if it is the person’s first seizure, or if the person 
is injured. While waiting for help to arrive, protect the affected person from injuring 
themselves on hard or sharp objects. If necessary, move the person to a safe place. 

Lay them on their side with their head supported to prevent it from hitting the floor. 
Loosen any tight clothing around their neck. Do not use force to hold the person or 
restrict their movements. Do not put anything in their mouth, including your fingers. 

 

 

Installation safety and protection from personal injury 

•

 

Installation must be performed by qualified personnel only and carried out in 
accordance with applicable regulations such as DIN VDE 0711-217. 

•

 

The safety of the installation is the responsibility of the installer. If in any doubt about 
the safety of a physical installation, consult a static engineer and seek advice from 
your GLP supplier before starting installation work. 

•

 

KNV Dot and Line fixtures and the KNV PSU are not portable when installed. 

•

 

Ensure that the supporting structure and installation hardware used can hold at least 

ten times the weight of the load that they support. 

•

 

Install fixtures and PSUs on structures or surfaces only as directed in this manual.  

•

 

Respect the safety limits given in this manual for the maximum number of fixtures 
that may be fastened to each other and suspended in columns or arrays. 

•

 

Columns and arrays of multiple fixtures must be protected from lateral forces that 
are intensified when the column or array acts as a lever. When forces are 
leveraged, there is an increased danger that sideways pressure at the bottom of an 
array can cause installation hardware at the top of the array to fail. Secure the 
extremities of columns and arrays against movement as described in this manual so 

that lateral forces cannot be applied to them. 

•

 

Install products only with hardware that is specifically designed and rated for its 
purpose. Do not use a safety cable as the primary means of support. Check that all 
installation hardware is in perfect condition. Fasteners must be steel grade 8.8 

strength or better. 

Summary of Contents for KNV Dot


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands