manualshive.com logo in svg

GLP KNV Dot, Quick Start And Safety Manual

Share
Download
GLP KNV Dot Quick Start And Safety Manual Download Page 27

German Light Products® 

 

 

KNV Dot and Line Quick Start and Safety Manual Rev. A 

27 

 

If there is any risk that the KNV Dot will cause injury or damage if it falls, secure it 
with an approved safety cable as described in ‘Securing with a safety cable’ on 
page 19. 

 

Fasten a KNV Dot under the first Dot 
by means of a GLP Slide Connector 
as described in ‘Fastening KNV Dots 

together’ on page 22. 

 

Continue adding KNV Dots as 
described above. Do not exceed a 
maximum of ten (10) KNV Dots in 
total for any column that is 
suspended using a GLP Half-Slide 

Connector. If you want to install 
more KNV Dots vertically below this 
column, you must create a new 
column with its own suspension point. 

 

Fasten the bottom of the column to 
secure anchoring points so that no 

point in the column can be pushed 
or pulled sideways. When 
immobilizing the bottom of the 
column in this way, do not increase 

the load on rigging hardware by 
applying downwards tension to the 
column. 

 

 

Figure 14. Single column 

of 10 x KNV Dots suspended using a 

GLP Half-Slide Connector 

KNV Dot 

Rigging 

Clamp  

13-55/45/15

GLP Half-Slide

Connector 

GLP Slide 

Connector 

Summary of Contents for KNV Dot


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands