manualshive.com logo in svg

GLP KNV Dot, Quick Start And Safety Manual

Share
Download
GLP KNV Dot Quick Start And Safety Manual Download Page 51

German Light Products® 

 

 

KNV Dot and Line Quick Start and Safety Manual Rev. A 

51 

12.

 

Connecting the PSU to control data 

Warning!

  

Check that all cables and connectors are suitable for the installation 
environment and application (see recommendations in ‘Avoiding damage’ 
on page 11). 

Keep unused connectors sealed with their rubber caps at all times. 
Do not allow any weight (in the form of cable runs, for example) to hang 
from connectors, as this may affect their sealing ability and allow water to 
enter connections. 

 
The KNV PSU supports USITT DMX 512A, Art-Net and sACN DMX control data signal 
protocols. It also supports RDM (Remote Device Management). 
Two types of data connection are available: 

•

 

Two 5-pin XLR connectors for IN and THRU connections on a DMX link using standard 

DMX protocol. Use standard DMX cable that is suitable for the installation 
environment if connecting to the PSU’s XLR connectors. 

•

 

Two EtherCON sockets for IN and THRU connections on a DMX data link using Art-
Net or sACN protocol. It makes no difference which socket you use for data IN and 

which for data THRU. Use CAT6 or better Ethernet cables for the data link if 
connecting to the PSU’s Ethernet ports. 
The EtherCON ports are failsafe. This means that Art-Net or sACN data will still be 
forwarded even if the KNV PSU is accidentally or deliberately powered off. 

 
If you would like advice with planning and installing a DMX link, your GLP supplier will 
be happy to provide assistance. 

Summary of Contents for KNV Dot


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands