Global American 3307800 User Manual Download Page 100

Page: 100 / 135

3307800

Page 85

NOTE:

Global American, INC. has a wide range of backplanes available.

Please contact your 3307800 vendor, reseller or a Global American,

INC. sales representative at [email protected] or visit

the Global American, INC. website

(http://www.Globalamericaninc.com) to find out more about the

available chassis.

5.6.2 Backplane Installation

Before the 3307800 can be installed into the chassis, a backplane must first be installed.

Please refer to the installation instructions that came with the backplane and the chassis to

see how to install the backplane into the chassis.

NOTE:

Global American, INC. has a wide range of backplanes available.

Please contact your 3307800 vendor, reseller or a Global American,

INC. sales representative at [email protected] or visit

the Global American, INC. website

(http://www.Globalamericaninc.com) to find out more about the

available chassis.

5.6.3 CPU Card Installation

To install the 3307800 CPU card onto the backplane, carefully align the CPU card interface

connectors with the corresponding socket on the backplane. To do this, please refer to the

reference material that came with the backplane. Next, secure the CPU card to the chassis.

To do this, please refer to the reference material that came with the chassis.

Summary of Contents for 3307800








































































































































Search results

Summary of Contents for 3307800

Reviews:

Related manuals for 3307800

Brands by name

Popular brands

Global American 3307800, User Manual

Search results

Summary of Contents for 3307800

Reviews:

Related manuals for 3307800

Brands by name

Popular brands