background image

1

LMS MG PIR CLS SENSOR-R

B29004001

307127

Presence detectors

EN

1.  Product characteristics

 

Passive infrared presence detector for ceiling installation

 

Circular detection area 360° (up to 491 m

2

 

Restriction of detection area with cover clips

 

Automatic lighting control with constant lighting control 
or switching operation 

 

Lighting dimmable in switching operation with or wit-
hout effect of daylight

 

Orientation light (standby function)

 

DALI solution for up to 3 flexibly addressable lighting 

channels

 

Easy, intuitive configuration of DALI groups

 

Mixed light measurement suitable for fluorescent lamps 

(FL/PL/ESL), halogen/incandescent lamps and LEDs

 

Adaptable 3-channel light measurement

 

Calibration of brightness measurement

 

Fully or semi-automatic operation, switchable

 

Brightness setpoint value adjustable in lux

 

Teach-in function via remote control or button

 

Self-learning time delay

 

Reduction of time delay when present briefly (short-term 

presence)

 

Detection sensitivity configurable

 

Connection option for up to 3 conventional buttons for 
manual dimming and switching

 

Flexible assignment of buttons to required lighting chan

-

nel by remote control

 

Behaviour upon button operation selectable

 

Scene functionality

 

Easy configuration of the energy-saving response with 

“eco plus” function

 

Test mode for checking function and detection area

 

Light test mode for checking the brightness threshold

 

Extension of detection area via Master/Master switching

 

Protection rating IP 54 (installed)

 

Ceiling installation in flush-mounted box

 

Accessories

: Surface mounting on ceilings possible with 

back box LMS MG SURFACE MNT FRAME (B29011002), 
optional; user remote control LMS MG USER REMOTE 
(B29012001), optional; app remote control LMS MG 
PROGRAM REMOTE BT (B29012003) optional, and the 
corresponding Glamox Sensor-app (iOS/Android); safety 
cover LMS SENSOR SAFETY COVER (B29011001), optional

2.  Safety

Danger of death through electric shock or fire!

 Installation should only be carried out  

by a qualified electrician!

WARNING

 

Work on electrical systems may only be carried out by 

qualified electricians or by instructed persons under the 
guidance and supervision of a qualified electrician in 

accordance with the technical regulations applying to 

electricity! 

 

Comply with the country-specific safety regulations for 
work on electrical systems! Ensure absence of voltage in 
the cable before installation!

 

The device is maintenance-free. If the device is opened 
or penetrated with any object, the guarantee shall lapse.

3.  Proper use

The presence detector is intended for indoor installation.

4.  Function

The presence detector is primarily used in offices, schools, 

conference rooms and corridors, as well as in homes, for easy 

and energy-efficient control of lighting. The lighting is accor

-

dingly influenced by switching or constant lighting control.

Function description

 Mixed light measurement 

 Presence detection

 Artificial light

 Push button for manual lighting control

 Incident daylight

Lighting channel C1, C2, C3 

The lighting is controlled by presence and brightness. Artificial 

lighting is switched on and regulated at a constant brightness 

level via the DALI interface in the event of too little daylight 

and when the room is occupied.

The lighting is switched off via the DALI interface if there is 

sufficient daylight or if the room is unoccupied. 

Up to 3 lighting groups (lighting channels C1 - C3) can be 

configured on one single DALI line. DALI devices can be 

addressed and grouped very easily and intuitively. A detailed 

description can be found in chapter „9. Start-up“.

Summary of Contents for B29004001












Reviews: