background image

P

IP

E

T

TIN

G

7

PIPETMAN® CLASSIC

 

|

 

USER’S GUIDE

SETTING THE VOLUME

 

PIPETMAN® CLASSIC

Chapter 3

PIPETTING

While many brands of tips can be used with 

the PIPETMAN® Classic, it is recommended to 

use PIPETMAN® DIAMOND Tips for optimum 

performance. These tips are made from pure 

polypropylene. Plastic tips are for a single 

application—they should not be cleaned for 

reuse.

Fitting the Tips

To fit a new PIPETMAN DIAMOND Tip, push 

the tip holder into the tip using a slight twisting 

motion to ensure a firm, airtight seal.

Fitting the Tips on P2 and P10 Models

NOTE

For the P2 and P10 models, a dual-

position adapter (plastic) is required 

to fit DL10 tips (long tips) or D10 tips 

(short tips). The metallic rod of the tip 

ejector is shaped so the adapter may 

be clipped to it in either position.

P2 and P10 models are delivered with the 

adapter in place, positioned in the longer slot, 

and ready to use DL10 tips. 

When D10 tips are used, the 

adapter must be repositioned 

in the shorter slot as follows:
1. 

Pull the adapter down from 

the metallic rod.

2.  Turn the adapter 180°.
3.  Refit the adapter so the 

end of the metallic rod 

engages the shorter slot of 

the adapter.

Short 

tips

Long 

tips

Figure 5

Dual-position 

adapter for P2 

and P10

NOTE

Dual-position 

adapter is 

autoclavable.

Summary of Contents for PIPETMAN Classic P10





























Reviews: