manualshive.com logo in svg

Gigamon GigaVUE H Series, Hardware Installation Manual

Share
Download
Gigamon GigaVUE H Series Hardware Installation Manual Download Page 18

AMI_BIOS_Images

The GigaVUE-TA25E has an AMI Basic Input/Output System (BIOS). The BIOS image is
packaged with the software image. The BIOS contents are stored in flash memory,
allowing the BIOS to be upgraded. There are two flash components, a primary and a
secondary.

The following CLI command displays the two flash components and indicates the BIOS
image from which the system booted using asterisks:

If there is a component failure in the primary flash, the GigaVUE-TA25E boots from a
backup golden BIOS image in the secondary flash. An SNMP trap can be configured to
be sent when the system has booted from the secondary flash. The trap may indicate
that the primary flash component needs to be serviced. The trap is as follows:

Air Flows Directions

The air flow direction is from the front of the GigaVUE-TA25E chassis to the rear. The rear-
mounted fans pull air from the front to the back of the chassis. For environments with
hot/cold aisles, install the chassis so the intake air at the front of the chassis is cold.

AC and DC Powered GigaVUE-TA25E Models

Gigamon provides both AC and DC-powered versions of the GigaVUE-TA25E. Refer to

Connecting Power to

GigaVUE-TA25E.

Battery Caution

A disposable, non-rechargeable, Real Time Clock (RTC) Lithium manganese dioxide
button battery is in the GigaVUE-TA25E. Note the following:

■

There is a risk of fire if the battery is replaced with an incorrect type.

Contents

18

GigaVUE-TA25E Hardware Installation Guide

Summary of Contents for GigaVUE H Series
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands