A.15.6
Option 27 Scan Calibration
1.
Set the UUT to 1 GHz, 0.0 dBm. Select VAR ATTN: ON.
2.
Using a Giga-tronics 8540 power meter (or equivalent), measure the RF output power of
the UUT (see the 8540 frequency value equal to the frequency being measured). Verify a
reading of 0.0 dBm
±
2 dB.
3.
Select relative mode on the 8540 power meter. Turn the UUT’s power off. Zero the
power meter, then turn the UUT’s power on.
4.
Set VAR ATTN to -50 dB. Adjust R65 on the A7 PC board for a reading of -50.0 dBm
(
±
2 dB).
5.
Set VAR ATTN to -10 dB. Adjust R9 on the A7 PC board for a reading of -10.0 dBm
(
±
2 dB).
6.
Repeat steps 4 and 5 until both readings are within specification.
7.
Step the VAR ATTEN depth from 0 to -60 dB in 10 dB steps, and verify that all
readings are within specification.
☛
NOTE: The power meter must be accurate to -65 dBm. Zeroing the power meter
every two minutes with the UUT’s RF power off is recommended.
8.
With the UUT’s frequency set to 5, 10, and 20 GHz, verify that readings at -10 dB and
-50 dB are within specification.
A.15.7
Option 27 Assemblies
The components required for Option 27 are listed below.
Diagrams for Option 27 are contained in Chapter 7.
29822 OPT 27 60 dB SCAN W/O OPT 26, Rev: A
Item
Part Number
Qty
Cage
Mfr’s Part Number
Description
1
004BA34300
1
58900
004BA34300
.01-20 GHZ SCAN
2
420CF41700
1
58900
420CF41700
CTR/SCAN MOUNT; GT9000/S
3
MRTL-22020
1
58900
MRTL-22020
COAX TRANS SWITCH
4
003AW02700
REF
58900
003AW02700
OPT 27; SCAN MOD W/L
5
WCAS-26004
1
58900
WCAS-26004
4" 26 GHz SEMI-FLEX COAX
6
WCAS-26005
1
58900
WCAS-26005
5" 26 GHz SEMI-FLEX COAX
8
WCAS-26008
1
58900
WCAS-26008
8" 26 GHz SEMI-FLEX COAX
9
WCAS-18104
1
58900
WCAS-18104
4" 18 GHz SEMI-FLEX COAX
11
WCAS-18001
-1
58900
WCAS-18001
1" 18GHZ SEMI-FLEX COAX
101
HBPP-25605
7
26233
NS137CR256R5
2-56 X 1/4 PAN
102
HBPP-44010
2
58900
HBPP-44010
4-40 X 5/8 PAN
103
HNKS-44004
3
96906
MS35649-***
4-40 KEP NUT
104
HWSS-20200
7
58900
HWSS-20200
#2 X 1/8 SPLIT LOCK
105
HWSS-40300
3
58900
HWSS-40300
#4 X 3/16 SPLIT LOCK
106
HBPP-44005
2
26233
NS137CR440R5
4-40 X 5/16 PAN
107
HLLT-40210
1
79963
505-120 # 4
#4 SOLDER LUG
A7
120BA15650
1
58900
120BA15650
SCAN MODULATION PCA;GT9000
A109
420BA41900
1
58900
420BA41900
SCAN MODULE I/F PCA
A3 U13
UMN0-27256
1
01295
TMS 27C256-15JL
AT27C256 PROM ERASABLE
A3 U14
UMN0-27256
1
01295
TMS 27C256-15JL
AT27C256 PROM ERASABLE
CR1
DSA0-04148
1
58900
DSA0-04148
1N4148 G.P. DIODE
Model GT 9000 Microwave Synthesizer
A-18
Manual No. 120AM00250, Rev C, September 1998
Summary of Contents for GT 9000
