GESTRA LRR 1-52 Original Installation & Operating Manual Download Page 18

Page: 18 / 72

LRR 1-52, LRR 1-53, URB 55 - USA - Installation & Operating Manual -

850703-00

Technical data for the URB 55

Supply voltage

■

24 V DC (

) +/- 20%; PELV / CLASS2

Power consumption

■

Max. 14.4 W

Current input

■

Max. 0.6 A (at 24 V)

Fuse

■

Internal, automatic

Interfaces for data transmission

■

2 x Ethernet 10/100 Mbit switched (Modbus TCP/IP)

■

1 x USB host port (versions 2.0 and 1.1)

■

1 x slot for SD card

Indicators and controls

■

Capacitive 5” touchscreen with LED backlight

■

Resolution 800 x 480 pixels (WVGA)

■

Brightness 200 Cd/m

, dimmable

■

Size (field of view) 110 mm x 65 mm

Protection

■

Front:

IP66 according to EN 60529

■

Back:

IP20 according to EN 60529

Admissible ambient conditions

■

Service temperature:

32 ° - 140 °F (0 ° - 60 °C)

■

Storage temperature:

-4 ° - 158 °F (-20 ° - 70 °C)

■

Transport temperature:

-4 ° - 158 °F (-20 ° - 70 °C)

■

Air humidity:

5% – 85% relative humidity, non-condensing

Enclosure

■

Material: Front (metal/glass) / back (metal enclosure for electronics)

■

Enclosure attachment with the supplied fastening elements

■

Intended for installation in a control cabinet or switch panel

For dimensions, see page 18

■

Front panel (W x H) 5.79 in (147 mm) x 4.21 in (107 mm)

■

Switch panel cutout (W x H) 5.35 in (136 mm) x 3.78 in (96 mm)

■

Mounting depth 2.05 in (52 mm) + 0.32 in (8 mm) protruding

Summary of Contents for LRR 1-52









































































Search results

Summary of Contents for LRR 1-52

Reviews:

Related manuals for LRR 1-52

Brands by name

Popular brands

GESTRA LRR 1-52, Original Installation & Operating Manual

Search results

Summary of Contents for LRR 1-52

Reviews:

Related manuals for LRR 1-52

Brands by name

Popular brands