GESTRA LRR 1-52 Original Installation & Operating Manual Download Page 13

Page: 13 / 72

LRR 1-52, LRR 1-53, URB 55 - USA - Installation & Operating Manual -

850703-00

Basic safety information

There is a risk of electric shock during work on electrical systems.

■

Always switch off the voltage to the equipment before performing work on the
terminal strips.

■

Check that the plant is not carrying live voltage before commencing work.

Faulty equipment is a danger to plant safety.

■

If the LRR 1-52, LRR 1-53 conductivity controller does not behave as expected, it
may be faulty.

■

Perform failure analysis.

■

Only replace faulty equipment with identical equipment from GESTRA AG.

Required personnel qualifications

Activity

Personnel

Integration in control system

Specialist staff

Plant designer

Installation/electrical connection/
bringing into service

Specialist staff

Electrician/installer

Operation

Boiler service technician Staff trained by the plant operator

Maintenance work

Specialist staff

Electrician

Setup work

Specialist staff

Plant construction

Fig. 2

Notes on product liability

The manufacturer cannot accept any liability for damages resulting from improper use of the
equipment.

Summary of Contents for LRR 1-52









































































Search results

Summary of Contents for LRR 1-52

Reviews:

Related manuals for LRR 1-52

Brands by name

Popular brands

GESTRA LRR 1-52, Original Installation & Operating Manual

Search results

Summary of Contents for LRR 1-52

Reviews:

Related manuals for LRR 1-52

Brands by name

Popular brands