GeoVision GV-Mobile NVR System User Manual Download Page 24

Page: 24 / 77

Getting Started

1. There are two options for connecting the power.

A. Connect the GV-Mobile NVR System to the vehicle’s power battery and ACC wire

using the supplied 3-pin terminal block. The system will automatically start after you
turn on the vehicle ignition. Power is supplied to the system as long as the vehicle
ignition is on.

Ground

Ignition

Power

Figure 3-2

B. Optionally purchase a power adapter from GeoVision. See 3.2

Turning on and off

the Power

2. Use the VGA cable or the DisplayPort cable to connect the unit to the monitor.

Note:

The GV-Mobile NVR System supports dual-monitor display. You can connect two

monitors by using the VGA connector and DisplayPort.

3. Connect one end to the Gigabit Ethernet port and the other end to Network by using the

RJ-45 cable.

4. Connect the keyboard and the mouse to the USB ports.

5. Connect the speaker to the Audio Line Out port.

6. Optionally connect the microphone to the Audio Microphone In port for two-way audio with

IP cameras.

7. Insert the 2.5” HDDs or SSDs into the storage slots. For details, see

3.3 Installing the

Storage Drive

After the unit is powered on, the Power Indicator LED (Figure 2-3) shows constant green.

Before recording, you need to format the storage drive and add it to the recording path of the
system. For formatting the storage drive, see

3.4 Formatting the Storage Drive

. For adding

the storage drive to the recording path, see

3.5 Adding the Storage Drive

to the Recording

Path.

Summary of Contents for GV-Mobile NVR System














































































Search results

Summary of Contents for GV-Mobile NVR System

Reviews:

Related manuals for GV-Mobile NVR System

Brands by name

Popular brands

GeoVision GV-Mobile NVR System, User Manual

Search results

Summary of Contents for GV-Mobile NVR System

Reviews:

Related manuals for GV-Mobile NVR System

Brands by name

Popular brands