manualshive.com logo in svg

GeoVision EFER3700-W, User Manual, Page: 52 / 209

Share
Download
GeoVision EFER3700-W User Manual Download Page 52

 

1.6.2  In-Ceiling Mount 

 

In this section, we introduce two types of in-ceiling mounts: General In-Ceiling Mount and 

GV-UNFE2503 / 2502. 

 

1.6.2.1  General In-Ceiling Mount 

In-Ceiling Mount allows the camera to be mounted into the ceiling, revealing a small portion 

of the camera. In-Ceiling Mount requires the ceiling board to be between 0.5 – 3.0 cm (0.2 – 

1.18 in) thick. 

    

Figure 1-34 

 

Note:

 This in-ceiling mount is not applicable to GV-UNFE2502 and the models with IR LED 

ring (GV-FE3403 / 5303 and GV-FER3403 / 5303), GV-FER5700 / 5701 / 12203 / 12700 
and GV-UNFE2503. 

 

1.  Place the installation sticker on the ceiling board, and cut the circle part out of the ceiling. 

To install GV-FE3402 / 5302 and GV-FER3402 / 5302, drill the 3 holes indicated as 

“Device”. 

         

 

Figure 1-35 

 

38 

Summary of Contents for EFER3700-W


















































































































































































































Reviews:

No comments